499296
10
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
DigitalBox Europe GmbH
Sandstraße 65 · D-40878 Ratingen
TROUBLE SHOOTING
Note:
If you have tried all of the actions suggested above, without solving the problem, please
contact your dealer or service provider.
Problem
The display on the front
panel does not light up.
No sound or picture, but the
front panel shows red light.
No sound or picture.
Bad picture/blocking error.
The picture is not shown
on the screen, when
switching on.
There is interference on
your digital satellite
channels, an existing
terrestrial channel or video
signal.
The RCU is not working.
What to do
Check that the main cable is plugged
into the power socket.
Press the standby button.
Adjust the dish. Check the signal level in
the Antenna Setup menu.
Check the cable connections, LNB and
other equipment connected between
the LNB and the receiver, or adjust the
dish.
Adjust the dish.
Connect a signal attenuator to the LNB
input.
Change to a larger dish.
Change to an LNB with lower noise
factor.
Change the LNB.
Check the UHF channel fi xed in your
system and tune the UHF channel
properly.
Change the output channel to a more
suitable channel, or connect the
system by SCART leads.
Change the batteries.
Aim RCU at the receiver, or check that
nothing blocks the front panel.
Possible causes
Main cable is not connected.
The receiver is in standby
mode.
The satellite dish is not
pointing at the satellite.
No signal or weak signal.
The satellite dish is not
pointing at the satellite.
Signal is too strong.
Satellite dish is too small.
LNB noise factor too high.
The LNB is faulty.
The system is connected by
RF leads.
The system is connected by
RF leads and the output
channel of the receiver
interferes with an existing
terrestrial channels or Video
signal.
Battery exhausted.
RCU is incorrectly aimed.
BDA Imperial SatBOX HD_GB_UES.in44 44BDA Imperial SatBOX HD_GB_UES.in44 44 04.04.2008 10:00:36 Uhr04.04.2008 10:00:36 Uhr
43 DVB-S Receiver
GB
Audio
Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPEG-II, Layer I/II Musicam
Sound Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stereo, Audio L, Audio R, Mono
Sampling Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 kHz, 44,1 kHz, 48 kHz
Output Impendance . . . . . . . . . . . . . . . . . . . . . . . . 600 Ω unbalance
Scart
Video Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CVBS, AUDIO R/L
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slow Blanking, Fast Blanking
Connector
SCART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TV & VCR SCART
Serial Data Interface . . . . . . . . . . . . . . . . . . . . . . . 9-pin D-sub connector (RS-232
HD Output
YPbPr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720P, 1080i
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720P, 1080i
Conditional Access
CA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DVB-CI Interface, 1 Smart Card
Microprocessor & Memory
Main Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sti 7100
Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mbyte
SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Mbyte
General
Control Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0/12 V (RCA)
Input Voltage Range . . . . . . . . . . . . . . . . . . . . . . . AC 90
~
250 V, 50
~
60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . Operatin Mode (30 Watt, max.)
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 x 145 x 45 mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,14 kg
Number of satellites . . . . . . . . . . . . . . . . . . . . . . . . 16 programmable
Number of channels . . . . . . . . . . . . . . . . . . . . . . . . 7.000 programmable
Multi language OSD . . . . . . . . . . . . . . . . . . . . . . . . 8
NIT, EPG, Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . (DVB EST300 472)
NTSC/PAL Conversion . . . . . . . . . . . . . . . . . . . . . Yes
IRD/PC to IRD data copy
Favorite, Sorting, Move, Delete . . . . . . . . . . . . . . Yes
SAT/TP/Channel . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Graphic Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16/5 (Color/Layer)
ICON Style OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
TECHNICAL SPECIFICATION
BDA Imperial SatBOX HD_GB_UES.in43 43BDA Imperial SatBOX HD_GB_UES.in43 43 04.04.2008 10:00:37 Uhr04.04.2008 10:00:37 Uhr
42Installation Guide
GB
SOFTWARE UPDATE
Turn on the Slave receiver. When the Slave receiver is powered ON, it will
automatically check the software status of master receiver, fi nd the “rom.bin” fi le to
be upgraded in master receiver and shift into Download mode.
During the download, Front panel of Slave Receiver will display the procedure
situation.
After completed Download, Slave Receiver automatically writes downloaded data in
its Flash Rom. The Slave receiver will automatically check the downloaded data.
Please wait until red light on the front panel turn on. If not, please re-do the above
procedure to download again or consult your local distributor for aid.
TECHNICAL SPECIFICATION
LNB
Frequency Range. . . . . . . . . . . . . . . . . . . . . . .950 - 2150 MHz
Frequency Level . . . . . . . . . . . . . . . . . . . . . . . .-65 to -25 dbm
DiSEqC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Version 1.2
22 kHz Tone . . . . . . . . . . . . . . . . . . . . . . . . . . .Frequency: 22 kHz, Amplitude: 0,8 V p-p
0/12 V Control . . . . . . . . . . . . . . . . . . . . . . . .0/12 VDC
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . .Horizontal: 18 V, Vertical: 13 V (600 mA max.)
Tuner
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Ω
Input & Loop Output Connector . . . . . . . . . .F Connector x 2
(1 Input, 1 Loop through Output)
IF Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . .Zero IF
Demodulator
Demodulation Waveform . . . . . . . . . . . . . . .QPSK, 8 PSK
Symbol Rate . . . . . . . . . . . . . . . . . . . . . . . . . . .2
~
45 Msps
FEC Decoder. . . . . . . . . . . . . . . . . . . . . . . . . . .1/2, 2/3, 3/4, 5/6, 7/8, 3/5, 4/5,
8/9, 9/10, AUTO
Video
Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MPEG-II and MPEG-I Compatible H. 264
Profi le & Level . . . . . . . . . . . . . . . . . . . . . . . . .Main Profi le, Main Level
Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .720 x 480 (NTSC), 720 x 576 (PAL)
Aspect Rate . . . . . . . . . . . . . . . . . . . . . . . . . . .4:3/16:9
Output Impedance . . . . . . . . . . . . . . . . . . . . . .75 Ω
Composite Output Level . . . . . . . . . . . . . . . . .1 ± 0,2 V p-p (75 Ω Load)
BDA Imperial SatBOX HD_GB_UES.in42 42BDA Imperial SatBOX HD_GB_UES.in42 42 04.04.2008 10:00:37 Uhr04.04.2008 10:00:37 Uhr
41 DVB-S Receiver
GB
Software Upgrade
If correct Port is selected, then the information of current version of the Receiver will
be displayed on the main menu.
If you want to upgrade now, then press “Upgrade Software” and fi nd the “rom.bin”
le to be up-graded in your PC. Then press “Open”.
During the download, your PC will display the procedure situation and the green light
on the front panel will turn on and fl icker.
After completed Download, receiver automatically writes downloaded data in its Flash
Rom. Be patient to wait till green light on the front panel off, and red light on the front
panel on.
Then plug off the receiver and re-power it on.
Read User Data
• If you select “Read User Data” button. You make any fi le, you can read your receiver
data. This receiver data will contain all the channels that are tuned by the receiver
The output will be a text fi le and you can also edit in your PC.
Write Factory Data
If you made your own data, you can upgrade in your receiver with this button.
If you want to write in your receiver, press “write factory data” button.
Select your own fi le.
During the download, the whole process is the same as the 2.2 software upgrade.
Master to Slave upgrading Instruction
Using a twisted/cross serial cable to connect the master receiver and slave receiver
with the RS232 port of them. Before connecting make sure that the cable is working.
Turn on the Master receiver and let it run completely. If the master receiver is con-
nected to The TV set, the picture and audio will be ceased when the upgrading begins
and resumes until the download is completely fi nished.
SOFTWARE UPDATE
BDA Imperial SatBOX HD_GB_UES.in41 41BDA Imperial SatBOX HD_GB_UES.in41 41 04.04.2008 10:00:38 Uhr04.04.2008 10:00:38 Uhr
40Installation Guide
GB
SOFTWARE UPDATE
Introduction
The objective is to list the steps for upgrading the FTLink.
Steps to be followed for PC to receiver upgrading
Connect Receiver to PC
Connect receiver to your PC using RS232C cable. (Don‘t attempt to connect the
PC to the receiver while either of the unit is powered on. It might caused a electrical
shock!)
Using a twisted/cross serial cable to connect the PC with the RS232 port of the
receiver. Before connecting make sure that the cable is working.
Turn on the Receiver
When the receiver is powered ON, red light on the front panel will turn on for a while
and then turn off.
Run FTLINK in your PC, then the upgrade main menu will be started.
From the PC run the FTLINK.exe fi le. Upon executing the exe the main menu of the
FTLink will be displayed.
Press “Setup Comm” to select Port connected to Receiver.
By pressing the “Setup Comm” button in the FTLink menu, select which COM port is
connected to the PC.
BDA Imperial SatBOX HD_GB_UES.in40 40BDA Imperial SatBOX HD_GB_UES.in40 40 04.04.2008 10:00:38 Uhr04.04.2008 10:00:38 Uhr
39 DVB-S Receiver
GB
Change Signature PIN
Do the same way as the above Change PIN.
Note: The signature PIN will be locked after the three erroneous attempts to enter
the correct PIN. If locked, please call the dealer for help.
Maturity Level
In Maturity level submenu, you can change the smart card s maturity level, which will
affect whether scrambled program is granced or not.
Es sThere are four levels for selection: A-Over18, X Erotic, G-For the family, PG-with
parental Guidance.
In order to change the maturity level, you must enter the correct PIN.
If all of the items are satisfi ed, then you can click change maturity level button.
A dialogue will tell you whether your change is succeeded or not.
Subscription Status
Know the detail information of Subscription Status.
Event Status
Know the detail information of Event Status.
Token Status
Know the detail information of Token Status.
E-Mail
All E-mails from the operator are listed in this window.
Product Ordering
Not available in this software.
CONDITIONAL ACCESS
BDA Imperial SatBOX HD_GB_UES.in39 39BDA Imperial SatBOX HD_GB_UES.in39 39 04.04.2008 10:00:39 Uhr04.04.2008 10:00:39 Uhr
38Installation Guide
GB
CONDITIONAL ACCESS
Smart Card
Select Smart Card item in Conditional
Access menu and press [OK] key to enter
into submenu.
There are 9 items in this menu:
Card Information
Change PIN
Change Signature PIN
Maturity Level
Subscription Status
Event Status
Token Status
Mail
Product Ordering
Use [PR+/PR] keys to select desired item and press [OK] to enter into its submenu.
Card Information
In Card Information sub-menu, you can know the basic information about this condi-
tional access such as Card Status, CAS System ID, Interface Version, Card Number,
Number of sessions, Country Indicator, and Maturity Level.
Change PIN
Changes PIN window is design for changing the smart card‘s PIN, which is required
if you want change the maturity level settings.
In order to change the PIN, you must know the current PIN also called the old PIN.
Input the new PIN and twice the PIN (New PIN and Confi rm PIN must be the same)
your want to set.
Move cursor to [OK] button and press [OK] key, and then system will
pop up a dialogue informing you the changing result.
Note that the PIN can only constructed with arabic numerals.
BDA Imperial SatBOX HD_GB_UES.in38 38BDA Imperial SatBOX HD_GB_UES.in38 38 04.04.2008 10:00:39 Uhr04.04.2008 10:00:39 Uhr
37 DVB-S Receiver
GB
The receiver makes you enjoy various scrambled channels encrypted by Viaccess, Na-
gravision, Irdeto, Conax, Cryptoworks and SECA.
Preparing
To be able to receive scrambled digital
satellite channels you need a Smartcard
and a Common Interface CA (Coniditonal
Access) module from the Service Provider
of your choice.
The Smartcard and the CA module may
also provide access to special menus
not described in this manual. If so, please
follow the instructions from the Service
Provider.
Only free to air channels are available
without Smartcard and CA module.
Insert the CA module in the slot of the
receiver and insert Smartcard to the CA
module entirely. If it is done properly, you
can enjoy scrambled channels accessed
by your CA module and Smartcard.
Note: The receiver has 2 slots of 2 CI modules.
Check Manager
Select Common Interface menu in the
Conditional Access menu and press [OK]
key. Then the receiver detects and shows
the CA module names, which you inserted
in the slots. Then select slot 1 or slot 2.
Then you can see the information, pro-
vided by the Program Provider.
Note: This information may be different from each Program Provider.
CONDITIONAL ACCESS
BDA Imperial SatBOX HD_GB_UES.in37 37BDA Imperial SatBOX HD_GB_UES.in37 37 04.04.2008 10:00:40 Uhr04.04.2008 10:00:40 Uhr
36Installation Guide
GB
ANTENNA DIRECTION HELP
Although you entered correct value in
Antenna Set up menu, if your antenna
is positioned incorrectly, you could not
receive signal from the Satellite.
So the receiver provides Antenna Direction
Help in order for you to have exact informa-
tion to direct your antenna toward a satellite.
First select your desired Satellite name
and then the location of selected satellite
will be displayed. In case the location of
the satellite is changed, you can re-set the
new location.
Second, enter the value of Longitude and
Latitude of your location.
If you entered correct value of your posi-
tion, place your cursor on Compute and
press [OK] key.
Then the receiver shows the exact infor-
mation of antenna pointing.
BDA Imperial SatBOX HD_GB_UES.in36 36BDA Imperial SatBOX HD_GB_UES.in36 36 04.04.2008 10:00:40 Uhr04.04.2008 10:00:40 Uhr
35 DVB-S Receiver
GB
System has provided several games to enjoy
your life.
Select Game item in the Game and Re-
ceiver Information sub menu, and press
[OK] key to enter into its window.
It contains six games of Russia Box,
Greedy snake, Ball, Five chess, Black-
White chess, and Push box.
Select the game that you want to play and
press [OK] key to enter into its window.
In each game window, If you don‘t know
how to play it, please press [INFO] key on
the RCU for help.
Receiver Information
You can get information about model, SW
Version, HW Version, Loader Version, Manu-
facture and date.
GAME
BDA Imperial SatBOX HD_GB_UES.in35 35BDA Imperial SatBOX HD_GB_UES.in35 35 04.04.2008 10:00:41 Uhr04.04.2008 10:00:41 Uhr
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Digitalbox IMPERIAL SatBOX HD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Digitalbox IMPERIAL SatBOX HD in de taal/talen: Engels als bijlage per email.

De handleiding is 2,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Digitalbox IMPERIAL SatBOX HD

Digitalbox IMPERIAL SatBOX HD Aanvulling / aanpassing - Deutsch - 7 pagina's

Digitalbox IMPERIAL SatBOX HD Gebruiksaanwijzing - Deutsch - 42 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info