499296

Digitalbox IMPERIAL SatBOX HD Handleiding

42
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
DigitalBox Europe GmbH
Sandstraße 65 · D-40878 Ratingen
TROUBLE SHOOTING
Note:
If you have tried all of the actions suggested above, without solving the problem, please
contact your dealer or service provider.
Problem
The display on the front
panel does not light up.
No sound or picture, but the
front panel shows red light.
No sound or picture.
Bad picture/blocking error.
The picture is not shown
on the screen, when
switching on.
There is interference on
your digital satellite
channels, an existing
terrestrial channel or video
signal.
The RCU is not working.
What to do
Check that the main cable is plugged
into the power socket.
Press the standby button.
Adjust the dish. Check the signal level in
the Antenna Setup menu.
Check the cable connections, LNB and
other equipment connected between
the LNB and the receiver, or adjust the
dish.
Adjust the dish.
Connect a signal attenuator to the LNB
input.
Change to a larger dish.
Change to an LNB with lower noise
factor.
Change the LNB.
Check the UHF channel fi xed in your
system and tune the UHF channel
properly.
Change the output channel to a more
suitable channel, or connect the
system by SCART leads.
Change the batteries.
Aim RCU at the receiver, or check that
nothing blocks the front panel.
Possible causes
Main cable is not connected.
The receiver is in standby
mode.
The satellite dish is not
pointing at the satellite.
No signal or weak signal.
The satellite dish is not
pointing at the satellite.
Signal is too strong.
Satellite dish is too small.
LNB noise factor too high.
The LNB is faulty.
The system is connected by
RF leads.
The system is connected by
RF leads and the output
channel of the receiver
interferes with an existing
terrestrial channels or Video
signal.
Battery exhausted.
RCU is incorrectly aimed.
BDA Imperial SatBOX HD_GB_UES.in44 44BDA Imperial SatBOX HD_GB_UES.in44 44 04.04.2008 10:00:36 Uhr04.04.2008 10:00:36 Uhr
43 DVB-S Receiver
GB
Audio
Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPEG-II, Layer I/II Musicam
Sound Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stereo, Audio L, Audio R, Mono
Sampling Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 kHz, 44,1 kHz, 48 kHz
Output Impendance . . . . . . . . . . . . . . . . . . . . . . . . 600 Ω unbalance
Scart
Video Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CVBS, AUDIO R/L
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slow Blanking, Fast Blanking
Connector
SCART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TV & VCR SCART
Serial Data Interface . . . . . . . . . . . . . . . . . . . . . . . 9-pin D-sub connector (RS-232
HD Output
YPbPr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720P, 1080i
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720P, 1080i
Conditional Access
CA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DVB-CI Interface, 1 Smart Card
Microprocessor & Memory
Main Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sti 7100
Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mbyte
SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Mbyte
General
Control Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0/12 V (RCA)
Input Voltage Range . . . . . . . . . . . . . . . . . . . . . . . AC 90
~
250 V, 50
~
60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . Operatin Mode (30 Watt, max.)
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 x 145 x 45 mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,14 kg
Number of satellites . . . . . . . . . . . . . . . . . . . . . . . . 16 programmable
Number of channels . . . . . . . . . . . . . . . . . . . . . . . . 7.000 programmable
Multi language OSD . . . . . . . . . . . . . . . . . . . . . . . . 8
NIT, EPG, Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . (DVB EST300 472)
NTSC/PAL Conversion . . . . . . . . . . . . . . . . . . . . . Yes
IRD/PC to IRD data copy
Favorite, Sorting, Move, Delete . . . . . . . . . . . . . . Yes
SAT/TP/Channel . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Graphic Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16/5 (Color/Layer)
ICON Style OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
TECHNICAL SPECIFICATION
BDA Imperial SatBOX HD_GB_UES.in43 43BDA Imperial SatBOX HD_GB_UES.in43 43 04.04.2008 10:00:37 Uhr04.04.2008 10:00:37 Uhr
42Installation Guide
GB
SOFTWARE UPDATE
• Turn on the Slave receiver. When the Slave receiver is powered ON, it will
automatically check the software status of master receiver, fi nd the “rom.bin” fi le to
be upgraded in master receiver and shift into Download mode.
• During the download, Front panel of Slave Receiver will display the procedure
situation.
• After completed Download, Slave Receiver automatically writes downloaded data in
its Flash Rom. The Slave receiver will automatically check the downloaded data.
• Please wait until red light on the front panel turn on. If not, please re-do the above
procedure to download again or consult your local distributor for aid.
TECHNICAL SPECIFICATION
LNB
Frequency Range. . . . . . . . . . . . . . . . . . . . . . .950 - 2150 MHz
Frequency Level . . . . . . . . . . . . . . . . . . . . . . . .-65 to -25 dbm
DiSEqC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Version 1.2
22 kHz Tone . . . . . . . . . . . . . . . . . . . . . . . . . . .Frequency: 22 kHz, Amplitude: 0,8 V p-p
0/12 V Control . . . . . . . . . . . . . . . . . . . . . . . .0/12 VDC
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . .Horizontal: 18 V, Vertical: 13 V (600 mA max.)
Tuner
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Ω
Input & Loop Output Connector . . . . . . . . . .F Connector x 2
(1 Input, 1 Loop through Output)
IF Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . .Zero IF
Demodulator
Demodulation Waveform . . . . . . . . . . . . . . .QPSK, 8 PSK
Symbol Rate . . . . . . . . . . . . . . . . . . . . . . . . . . .2
~
45 Msps
FEC Decoder. . . . . . . . . . . . . . . . . . . . . . . . . . .1/2, 2/3, 3/4, 5/6, 7/8, 3/5, 4/5,
8/9, 9/10, AUTO
Video
Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MPEG-II and MPEG-I Compatible H. 264
Profi le & Level . . . . . . . . . . . . . . . . . . . . . . . . .Main Profi le, Main Level
Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .720 x 480 (NTSC), 720 x 576 (PAL)
Aspect Rate . . . . . . . . . . . . . . . . . . . . . . . . . . .4:3/16:9
Output Impedance . . . . . . . . . . . . . . . . . . . . . .75 Ω
Composite Output Level . . . . . . . . . . . . . . . . .1 ± 0,2 V p-p (75 Ω Load)
BDA Imperial SatBOX HD_GB_UES.in42 42BDA Imperial SatBOX HD_GB_UES.in42 42 04.04.2008 10:00:37 Uhr04.04.2008 10:00:37 Uhr
41 DVB-S Receiver
GB
Software Upgrade
• If correct Port is selected, then the information of current version of the Receiver will
be displayed on the main menu.
• If you want to upgrade now, then press “Upgrade Software” and fi nd the “rom.bin”
fi le to be up-graded in your PC. Then press “Open”.
• During the download, your PC will display the procedure situation and the green light
on the front panel will turn on and fl icker.
• After completed Download, receiver automatically writes downloaded data in its Flash
Rom. Be patient to wait till green light on the front panel off, and red light on the front
panel on.
• Then plug off the receiver and re-power it on.
Read User Data
• If you select “Read User Data” button. You make any fi le, you can read your receiver
data. This receiver data will contain all the channels that are tuned by the receiver
The output will be a text fi le and you can also edit in your PC.
Write Factory Data
• If you made your own data, you can upgrade in your receiver with this button.
• If you want to write in your receiver, press “write factory data” button.
• Select your own fi le.
• During the download, the whole process is the same as the 2.2 software upgrade.
Master to Slave upgrading Instruction
• Using a twisted/cross serial cable to connect the master receiver and slave receiver
with the RS232 port of them. Before connecting make sure that the cable is working.
• Turn on the Master receiver and let it run completely. If the master receiver is con-
nected to The TV set, the picture and audio will be ceased when the upgrading begins
and resumes until the download is completely fi nished.
SOFTWARE UPDATE
BDA Imperial SatBOX HD_GB_UES.in41 41BDA Imperial SatBOX HD_GB_UES.in41 41 04.04.2008 10:00:38 Uhr04.04.2008 10:00:38 Uhr
40Installation Guide
GB
SOFTWARE UPDATE
Introduction
The objective is to list the steps for upgrading the FTLink.
Steps to be followed for PC to receiver upgrading
Connect Receiver to PC
• Connect receiver to your PC using RS232C cable. (Don‘t attempt to connect the
PC to the receiver while either of the unit is powered on. It might caused a electrical
shock!)
• Using a twisted/cross serial cable to connect the PC with the RS232 port of the
receiver. Before connecting make sure that the cable is working.
• Turn on the Receiver
When the receiver is powered ON, red light on the front panel will turn on for a while
and then turn off.
• Run FTLINK in your PC, then the upgrade main menu will be started.
From the PC run the FTLINK.exe fi le. Upon executing the exe the main menu of the
FTLink will be displayed.
• Press “Setup Comm” to select Port connected to Receiver.
By pressing the “Setup Comm” button in the FTLink menu, select which COM port is
connected to the PC.
BDA Imperial SatBOX HD_GB_UES.in40 40BDA Imperial SatBOX HD_GB_UES.in40 40 04.04.2008 10:00:38 Uhr04.04.2008 10:00:38 Uhr
39 DVB-S Receiver
GB
Change Signature PIN
Do the same way as the above Change PIN.
Note: The signature PIN will be locked after the three erroneous attempts to enter
the correct PIN. If locked, please call the dealer for help.
Maturity Level
In Maturity level submenu, you can change the smart card s maturity level, which will
affect whether scrambled program is granced or not.
• Es sThere are four levels for selection: A-Over18, X Erotic, G-For the family, PG-with
parental Guidance.
• In order to change the maturity level, you must enter the correct PIN.
• If all of the items are satisfi ed, then you can click change maturity level button.
• A dialogue will tell you whether your change is succeeded or not.
Subscription Status
Know the detail information of Subscription Status.
Event Status
Know the detail information of Event Status.
Token Status
Know the detail information of Token Status.
E-Mail
All E-mails from the operator are listed in this window.
Product Ordering
Not available in this software.
CONDITIONAL ACCESS
BDA Imperial SatBOX HD_GB_UES.in39 39BDA Imperial SatBOX HD_GB_UES.in39 39 04.04.2008 10:00:39 Uhr04.04.2008 10:00:39 Uhr
38Installation Guide
GB
CONDITIONAL ACCESS
Smart Card
• Select Smart Card item in Conditional
Access menu and press [OK] key to enter
into submenu.
• There are 9 items in this menu:
• Card Information
• Change PIN
• Change Signature PIN
• Maturity Level
• Subscription Status
• Event Status
• Token Status
• Mail
• Product Ordering
• Use [PR+/PR] keys to select desired item and press [OK] to enter into its submenu.
Card Information
In Card Information sub-menu, you can know the basic information about this condi-
tional access such as Card Status, CAS System ID, Interface Version, Card Number,
Number of sessions, Country Indicator, and Maturity Level.
Change PIN
Changes PIN window is design for changing the smart card‘s PIN, which is required
if you want change the maturity level settings.
• In order to change the PIN, you must know the current PIN also called the old PIN.
• Input the new PIN and twice the PIN (New PIN and Confi rm PIN must be the same)
your want to set.
• Move cursor to [OK] button and press [OK] key, and then system will
pop up a dialogue informing you the changing result.
• Note that the PIN can only constructed with arabic numerals.
BDA Imperial SatBOX HD_GB_UES.in38 38BDA Imperial SatBOX HD_GB_UES.in38 38 04.04.2008 10:00:39 Uhr04.04.2008 10:00:39 Uhr
37 DVB-S Receiver
GB
The receiver makes you enjoy various scrambled channels encrypted by Viaccess, Na-
gravision, Irdeto, Conax, Cryptoworks and SECA.
Preparing
• To be able to receive scrambled digital
satellite channels you need a Smartcard
and a Common Interface CA (Coniditonal
Access) module from the Service Provider
of your choice.
• The Smartcard and the CA module may
also provide access to special menus
not described in this manual. If so, please
follow the instructions from the Service
Provider.
• Only free to air channels are available
without Smartcard and CA module.
• Insert the CA module in the slot of the
receiver and insert Smartcard to the CA
module entirely. If it is done properly, you
can enjoy scrambled channels accessed
by your CA module and Smartcard.
Note: The receiver has 2 slots of 2 CI modules.
Check Manager
• Select Common Interface menu in the
Conditional Access menu and press [OK]
key. Then the receiver detects and shows
the CA module names, which you inserted
in the slots. Then select slot 1 or slot 2.
• Then you can see the information, pro-
vided by the Program Provider.
Note: This information may be different from each Program Provider.
CONDITIONAL ACCESS
BDA Imperial SatBOX HD_GB_UES.in37 37BDA Imperial SatBOX HD_GB_UES.in37 37 04.04.2008 10:00:40 Uhr04.04.2008 10:00:40 Uhr
36Installation Guide
GB
ANTENNA DIRECTION HELP
Although you entered correct value in
Antenna Set up menu, if your antenna
is positioned incorrectly, you could not
receive signal from the Satellite.
So the receiver provides Antenna Direction
Help in order for you to have exact informa-
tion to direct your antenna toward a satellite.
• First select your desired Satellite name
and then the location of selected satellite
will be displayed. In case the location of
the satellite is changed, you can re-set the
new location.
• Second, enter the value of Longitude and
Latitude of your location.
• If you entered correct value of your posi-
tion, place your cursor on Compute and
press [OK] key.
• Then the receiver shows the exact infor-
mation of antenna pointing.
BDA Imperial SatBOX HD_GB_UES.in36 36BDA Imperial SatBOX HD_GB_UES.in36 36 04.04.2008 10:00:40 Uhr04.04.2008 10:00:40 Uhr
35 DVB-S Receiver
GB
System has provided several games to enjoy
your life.
• Select Game item in the Game and Re-
ceiver Information sub menu, and press
[OK] key to enter into its window.
• It contains six games of Russia Box,
Greedy snake, Ball, Five chess, Black-
White chess, and Push box.
• Select the game that you want to play and
press [OK] key to enter into its window.
• In each game window, If you don‘t know
how to play it, please press [INFO] key on
the RCU for help.
Receiver Information
You can get information about model, SW
Version, HW Version, Loader Version, Manu-
facture and date.
GAME
BDA Imperial SatBOX HD_GB_UES.in35 35BDA Imperial SatBOX HD_GB_UES.in35 35 04.04.2008 10:00:41 Uhr04.04.2008 10:00:41 Uhr
34Installation Guide
GB
TIMER
The TIMER function allows you to program the timer with various ways. This function
is one of the strong point of the receiver.
To activate the Turn On Time and/or Turn Off Time, select YES and enter your
desired time.
Note: The receiver display the time which is given by satellite, so there may be some
differences between actual time and the receiver‘s time.
Time Adjust
• Set local time: Adjust your local time.
• Summer time: If you are in summer time,
select ON.
Note: Time Adjust is default for the fi rst
time.
Time Reservation
• Time Reservation allows you to program
the various timer function.
• To activate the Turn on time and/or Turn
off the time , select YES and enter your
desired time.
• And you can also select channel which will
be turn on or turn off.
• You can set the timer daily, weekly,
monthly and yearly.
BDA Imperial SatBOX HD_GB_UES.in34 34BDA Imperial SatBOX HD_GB_UES.in34 34 04.04.2008 10:00:42 Uhr04.04.2008 10:00:42 Uhr
33 DVB-S Receiver
GB
• Das Then EPG box will be displayed.
• You can see the channel in the PIG
screen, channel list in the left side and
Program schedule for selected channel
will be displayed in the right side. The time
will be displayed relating to the program
schedule.
• Select one channel and placing the mark
on the time of Program name which detail
information you want to know.
Then you can see blue button, if there is details information of the channel. And press
Detail (blue key) key on the RCU, then detail information box will be displayed.
• If you want to check the former or later information of the channel, please press
+6:00 key (yellow key) or 6:00 key (green key) on the RCU.
Note: A “No data available” message will be shown if the selected channel does not
provide EPG date.
Special Channel EPG
During the normal mode, if you want to look
up the program forecast in one week of
present playing channels, including channel
name, playing time, program content and so
on, please twice press [INFO] key on the RCU
to enter into the following window:
• The present channel name is at the top of
window.
• The date shows at the left-up corner.
• The user can select playing date through [LEFT/RIGHT] key in the time compositor
from Sunday to Saturday.
• The next row shows the current condition of window. EPG will show “researching EPG
information...” while searching the current channel. After searching, it will show “EPG
information”.
• “Duration & Title” in the next row means that the contents in the following massage
box is the future program name and the time. User can move the point up and down
to select the programs by the right box. At this moment, if the detailed infor-
mation exists, it will be showed in the information box under the “Detail”. If no such
introduction, “No Detail” will appear.
EPG (Electronic Program Guide)
BDA Imperial SatBOX HD_GB_UES.in33 33BDA Imperial SatBOX HD_GB_UES.in33 33 04.04.2008 10:00:43 Uhr04.04.2008 10:00:43 Uhr
32Installation Guide
GB
CHANNEL MANAGER/EPG
Sort Channel
• In Main Page, press [MENÜ] key on the
RCU and select Sort on the command
menu.
• This Sort menu has its sub command and
it allows you to sort the channels as you
like. You can sort the channels by Favorite,
Lock, Scramble and Program name.
• Place the cursor on your desired line, and
then press [OK] key.
• And check whether the channels are sorted properly on the channel list or not.
Note: Radio Channel Manager has the same operation as TV channel Manager.
The receiver provides EPG function for you
to get access to the TV Guide(or Radio Guide
if you are listening to radio channels) which
will show the titles and other information of
the current and next programs on different
channels. The information is only available
from the network to which the channel you
are watching belongs.
EPG (Electronic Program Guide)
BDA Imperial SatBOX HD_GB_UES.in32 32BDA Imperial SatBOX HD_GB_UES.in32 32 04.04.2008 10:00:44 Uhr04.04.2008 10:00:44 Uhr
31 DVB-S Receiver
GB
Rename Channel
• In Main Page, press [MENU] key on the
RCU, and then select Rename on the com-
mand menu.
• This Rename command allow you to
rename the channel.
• First select the channel to be renamed
and press [OK] key, then, keypad dialog
box will be displayed.
• Edit your desired name entering word or
number.
• To delete characters or numbers, select in the keypad dialog.
• And check whether the channel name is changed on channel list properly or not.
Delete Channel
• In the Channel manager, you can enter
Delete CH mode, if you press Delete key
(red key) on the RCU. Then, if you press
Delete key (red key) repeatedly, the mode
will be changed to be Delete TP -> Delete
Satellite -> Delete All -> Delete CH.
• This Delete command allows you to delete
the channel permanently. First select the
channels, which you want to delete, then
selected channel number will be marked
to X. If you cancel the selection, press
[OK] key again, then the marked number
will be back.
• If you decided to delete, press [EXIT] key and then Message box will be displayed.
Press [OK] to delete.
• And check whether the channel number is deleted on channel list or not.
Warning: The deleted channel can not be recovered unless you search again. Please be
careful when you decide to delete channel.
CHANNEL MANAGER
BDA Imperial SatBOX HD_GB_UES.in31 31BDA Imperial SatBOX HD_GB_UES.in31 31 04.04.2008 10:00:45 Uhr04.04.2008 10:00:45 Uhr
30Installation Guide
GB
CHANNEL MANAGER
Move Channel
• In the TV channel manager page, press
[Move] key (yellow key) on the RCU.
• Select a channel by pressing [OK] key and
move the cursor to the location in which
you want to move the selected channel
and press [OK] key.
• Then, you will fi nd the selected channel is
moved to the desired location and channel
no. also changed in order accordingly.
• And check whether the channel number is
changed on the channel list.
Lock Channel
• Drücken In the TV channel manager
page, press [Lock] key (blue key) on
the RCU.
• This Lock command allow you to lock the
channel. First select the channel, which
you want to lock, and press [OK] key
and then will be marked at rear of your
selected channel name.
Note: To perform this function, you should set up the Parental Lock in advance.
BDA Imperial SatBOX HD_GB_UES.in30 30BDA Imperial SatBOX HD_GB_UES.in30 30 04.04.2008 10:00:46 Uhr04.04.2008 10:00:46 Uhr
29 DVB-S Receiver
GB
Favorite Channel
• When you select channel manager, default
favorite list will be showed on the screen
as Favorite 1.
• Select your favorite channel and then
press [OK] key. Then will be marked at
rear of your selected channel name.
• Wenn And if you want to delete the chan-
nel name in the favorite channel list, press
[OK] key once again, then the mark will
be disappeared.
• After the selection of favorite channels press [EXIT] key twice to save data and press
[FAV] key repeatedly to see if each of the favorite groups are properly selected.
• means scrambled channel.
How to make favorite group
• When you enter channel manager, the default favorite group will be showed once on
the screen as Favorite 1.
• If you press favorite key (green key) on the RCU, new favorite group will be created
newly as Favorite 2 and Favorite 3.
How to edit the name of favorite group
• In the favorite mode, press [MENU] key
on the RCU then the commend box will be
displayed on the screen.
• Select “Rename Favorite group” in the
commend box.
• You can edit the name by using keypad.
CHANNEL MANAGER
BDA Imperial SatBOX HD_GB_UES.in29 29BDA Imperial SatBOX HD_GB_UES.in29 29 04.04.2008 10:00:47 Uhr04.04.2008 10:00:47 Uhr
28Installation Guide
GB
CHANNEL MANAGER
The receiver provides most powerful channel managing function in the world and this
function allows you to have a more interesting and useful operation as well as watching
channels simply.
Manager
• Manager consists of TV program
Manager, Radio Program Manager.
Press [OK] key placing the cursor on the
TV Program Manager.
Note: Since the usage of Radio Program
Manager is same as that of TV Program
Manager, in this manual only TV Channel
manager is explained.
• In the left side of TV Program Manager menu, you can see the channel list which
were already searched and in the right side, you can watch the current channel in
small Picture in Graphic (PIG) mode (1/9 size of the normal) and you can see channel
information under the PIG screen.
When you move cursor from one channel to another, PIG will change accordingly.
• You can utilize those color keys on the
RCU as below:
• Delete mode (red key)
• Favorite mode (green key)
• Move mode (yellow key)
• Lock mode (blue key)
Also, press [MENU] key on the RCU, then
command menu will be displayed.
TV channel manager has 3 commands as
below:
• Rename Favorite group
• Rename
• Sort
BDA Imperial SatBOX HD_GB_UES.in28 28BDA Imperial SatBOX HD_GB_UES.in28 28 04.04.2008 10:00:47 Uhr04.04.2008 10:00:47 Uhr
27 DVB-S Receiver
GB
Volume & Audio Control
• Volume Control: To increase or decrease
volume, use key on the RCU or
[VOL] on the front panel.
Note: The receiver has 32 volume levels
and this shall be controlled from the
adjusted volume level of your TV.
• Mute: To mute the sound, press button on the RCU. To bring back the normal
sound, press this key once again.
• Audio Control: Press the key repeatedly to select one of three possible Audio
settings (Left, Right and Stereo). The current audio condition will be displayed in the
channel information.
• Language Selection: Press the [AUDIO] key on the RCU repeatedly to select audio-
language. This is dependent on the transmission of audio signal which supports
multi-language.
Favorite List
• If you want to have a favorite group lists
which were made in the channel manager,
please press [FAV] key on the RCU.
• The method of grouping of favorite chan-
nel list will be explain in the favorite Chan-
nel (page 29).
GENERAL VIEWING FUNCTION
BDA Imperial SatBOX HD_GB_UES.in27 27BDA Imperial SatBOX HD_GB_UES.in27 27 04.04.2008 10:00:48 Uhr04.04.2008 10:00:48 Uhr
26Installation Guide
GB
GENERAL VIEWING FUNCTION
Pause the frame
• Press [PAUSE] key on the RCU to pause the screen.
• To bring it back to the normalmode, press [PAUSE] key once again.
Previous channel recall
• Press [PR] key on the RCU to move the previous channel which you watched before.
Channel Information
• Every time you change channels, you will
receive program information for a few
seconds.
• While watching channel, you can see the
current channel information anytime,
pressing [INFO] key on the RCU.
Note: Channel information will be displaying for 6 seconds and disappeared. You can
adjust the display time interval from 3 to 30 seconds.
BDA Imperial SatBOX HD_GB_UES.in26 26BDA Imperial SatBOX HD_GB_UES.in26 26 04.04.2008 10:00:49 Uhr04.04.2008 10:00:49 Uhr
25 DVB-S Receiver
GB
• Move the point to the FAVORITE by using
[PR+/PR-] on the RCU, and then eight
functional options (favorite 1 to favorite 8)
will fl ip out.
• The middle list will show all the satellite
from which the programs in the receiver
come when selecting SATELLITE ways to
arrange the programs. The right list show
all the programs related to the selected
satellite.
• When using a-z to arrange the programs,
the middle list will show 26 English
characters and etc, which is 27
selecting items in total. When one
character is chosen, the list in the right
side will show all the programs which are
beginning with such character. When etc
has been chosen, the list in the right side
will show all the programs which are not
beginning with such character.
• CAS is chosen to arrange the programs,
the two items FTA and SCRAMBLE will
appear in the middle list. When FTA
has been chosen, all the free programs
stored in the receiver will be listed in the
right side. When SCRAMBLE is chosen,
all the scrambled programs saved in the
receiver will come out at the right side.
GENERAL VIEWING FUNCTION
BDA Imperial SatBOX HD_GB_UES.in25 25BDA Imperial SatBOX HD_GB_UES.in25 25 04.04.2008 10:00:50 Uhr04.04.2008 10:00:50 Uhr
24Installation Guide
GB
GENERAL VIEWING FUNCTION
Select Channel
The following describes the basic functions of your receiver while watching satellite TV or
listening to satellite radio.
While watching, the current channel information will be shown on the bottom of the
screen if you press [INFO] button on the RCU.
• If you want to select channel, use [CH]
key on the front panel or [PR+/PR-] key
on the RCU or numeric key on the RCU to
select a channel and press [OK] key on
the RCU.
In addition to the above normal function,
the receiver provide more convenient
channel change function.
• While watching, press [OK] key on the RCU. Then channel list will be displayed on the
screen. If press [EXIT] key, the channel list will be disappeared.
• To select a channel, go up and down of this channel list and place cursor on a desired
channel. Then, press [OK] key to watch the selected channel.
• If you press -Tkey on the RCU, channel list will more upgrade down page by page
• The function category items (From All
to Cas) are listed on the left top corner.
The yellow cursor moves up and down by
pressing [PR+/PR-] keys on RCU. When
a function item like All is highlighted, a
relevant channel list appears on the right
of screen. The Yellow cursor moves to
Channel list by pressing [V+]. Move the
cursor up and down and press [OK] for
the programs desired to view program
and exit the current window. Move the
cursor to function list by pressing Volume-.
BDA Imperial SatBOX HD_GB_UES.in24 24BDA Imperial SatBOX HD_GB_UES.in24 24 04.04.2008 10:00:51 Uhr04.04.2008 10:00:51 Uhr
23 DVB-S Receiver
GB
How to use Install Lock:
• Enter the current password.
• Select ON of Install Lock.
• Enter new password.
• Confi rm your new password entering new
password again.
• Exit this menu.
• Select any menu and press [OK] on the
RCU.
•
Then Enter Password Box will be displayed.
• Unless enter correct password, you can
not run any menu.
Note: Default password is 0000.
Warning: Do not forget your password in order not to fail to operate the receiver.
Werkseinstellung
• If you want to bring the receiver back to
the factory default condition, select Fac-
tory Default and press [OK] key.
• Then Warning message will be displayed.
• To confi rm select OK and press [OK].
Warning: You will lose all of data and
information which was installed.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in23 23BDA Imperial SatBOX HD_GB_UES.in23 23 04.04.2008 10:00:52 Uhr04.04.2008 10:00:52 Uhr
22Installation Guide
GB
Parental Lock
This function allows you to lock the channel
with your password in order to prevent from
accessing the channel by your children or any
other person.
And also you can protect your installed data
and information using Install Lock.
How to change Password:
• Enter the current password.
• Select ON of Parental Lock.
• Enter new password.
• Confi rm your new password entering new password again.
Note: Default password is 0000.
Warning: Once you change password, please do not forget and keep well.
How to use Parental Lock:
• If you activate parent lock function, go to
the TV Channel Manager Page.
• Press Lock key (blue key) on the RCU.
• Select channel which you want to lock.
• Press OK then symbol is marked.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in22 22BDA Imperial SatBOX HD_GB_UES.in22 22 04.04.2008 10:00:52 Uhr04.04.2008 10:00:52 Uhr
21 DVB-S Receiver
GB
System Setting
System Setting menu allows you to change the principal option and to set other items
proper to your environment by pressing [OK] key on the RCU.
• OSD Language: Select your desired language.
• Audio Language: Select your desired audio language to be in the top priority under
the condition that this language is supported from the channel.
• LNB power: If your receiver is connected to LNB, select EIN. But if your receiver is
connected to other receiver through Loop Through support, you should check which
receiver is connected directly to LNB. In case if that other receiver is directly con-
nected to LNB, select OFF.
• Video Format: Select the desired video format among LetterBox, PanScan, Combined
and Ignore.
• Scan Format: If your TV support 16:9 screen format and selected channel provides
16:9 format program, select 16:9.
• TV type: Select the type according to your TV type.
• Transparent Rate Adjustment: Transparent Rate is used to adjust transparent rate
of all the menus when appearing on the screen. The lowest value 1 means the most
transparency, the highest value 10 means opacity. Do the setups as you like.
• Start On Channel: Press [OK] it will pop up a dialogue: “Are you sure to activate the
Start On Channel?”. You can select OK or EXIT. If you press [OK] key, then the chan-
nel list is displayed. You can select one channel of the list, the selected channel starts
whenever you turn on the receiver.
• HD Format: Select among 1080i, 720p,
576p.
• HD Colorspace: Select between RGB and
YCbCr.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in21 21BDA Imperial SatBOX HD_GB_UES.in21 21 04.04.2008 10:00:53 Uhr04.04.2008 10:00:53 Uhr
20Installation Guide
GB
• Delete TP: If you want to delete a trans-
ponder, please select the Transponder
what you want to delete and then press
[MENU] key on the RCU to display
command box. Then select Delete TP
command and the confi rm message box
will be displayed.
Channel Search-2) USALS
Since the same operation, please refer to the above Channel Search-1) DiSEqC 1.2.
Channel Search-3) Fixed
• Antenna: Select your antenna number.
• Satellite: Select desired a satellite using
keys or if you press [OK] key, the list of
satellite will be displayed so that you can
select easily.
You can see the information of selected
satellite in the right side.
• Edit Mode: If you want to edit those pre-
programmed data such as Transponder,
Frequency, Symbol Rate, Polarization and
22 KHz, please press EDIT mode key (red
key) on the RCU to display the command
box. And then you can move to those
columns to change the value.
• Please refer to DiSEqC 1.2 type antenna.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in20 20BDA Imperial SatBOX HD_GB_UES.in20 20 04.04.2008 10:00:54 Uhr04.04.2008 10:00:54 Uhr
19 DVB-S Receiver
GB
• Search 1 Sat: Allows you to search channels with convenient options as follows,
select one using arrow keys.
• Search 1 SAT: Search channels for
one satellite which selected on Satellite
column.
• Search TP: Search channels in one TP
which selected on TP column.
• Search Network: Search channels for
the network related the TP.
• Search all SAT: Search all channels at
once which you searched all satellite.
Notes: In “Search 1 SAT” and “Search TP” function,you can switch “FTA+ “ for
free to air and scramb channels model,”FTA” for free to air channels model, “ “ for
scramb channels model by RCU.
The receiver will automatically search
the channel for TV and Radio and during
this procedure you can see the already
searched channels in the Searched List
Box on the screen.
If completed searching channel, cursor
will be placed on COMPLETE automati-
cally, then press [OK] button.
• Set PID: If you want to set PID (Packet
Identifi er) manually, press Set PID key
(green key) on the RCU to display the SET
PID menu.
In Set PID menu, enter the correct value
and select OK.
• Sat name edit: If you want to change sat-
ellite name, select the satellite and press
Sat Name Edit key (yellow key) on the RCU
to display Keypad Dialog box. Using arrow
key on the RCU, you can edit the satellite
name.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in19 19BDA Imperial SatBOX HD_GB_UES.in19 19 04.04.2008 10:00:55 Uhr04.04.2008 10:00:55 Uhr
18Installation Guide
GB
Channel Search-1) DiSEqC 1.2
• Antenna: Select your antenna number.
• Satellite: The satellite here is determined
by the selected number in above Antenna
item. You can see the information of
selected satellite in the right side.
Edit Mode: If you want to edit those pre-
programmed data such as Transponder,
Frequency, Symbol Rate, Polarization and
22 KHz, please press Edit mode key (red
key) on the RCU. And then you can move
into those columns to change the value.
• Position: After selecting a satellite, please
select Position button and then keep
pressing or key on the RCU until
selected satellite is locked. If the satellite
is locked correctly, the color of signal label
bar will be changed to yellow.
When you press [OK] key on the RCU,
the message of “Would you like to set
the value of current positioner” will be
displayed for your confi rmation.
• Transponder: Select desired a transpond-
er using keys or if you press [OK]
key, the Down List Box will be displayed so
that you can select easily.
• Frequency & Symbol Rate: Edit Frequency and Symbol Rate you want.
• Polarization: Select Hor or Ver.
• 22 kHz: Select ON or OFF.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in18 18BDA Imperial SatBOX HD_GB_UES.in18 18 04.04.2008 10:00:56 Uhr04.04.2008 10:00:56 Uhr
17 DVB-S Receiver
GB
Antenna Setup-3) Fixed
• Antenna: You can select maximum 16
antenna with the combination switches.
• Type: Select your antenna type to be fi xed.
• Satellite: Select satellite you want.
• LNB Type: Select your LNB type. If you
have universal LNB, select Univ.
• LNB Freq.: Enter the proper LNB
frequency referring to your LNB using
numeric key on the RCU. If you have a dual
LNB, enter the proper value in the both of
value box.
• Switches (0/12 Volt, 22KHz Tone,
DiSEqC): You can select the switches with
which you want to confi gure the antenna.
• Transponder: Select fi rst transponder you want.
• After setting all necessaries, please [EXIT] to fi nish antenna setup menu. The
message of “Are you sure to change the confi guration of Antenna setup?” will be
displayed. Please select [OK] button on the screen and then wait for saving a data.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in17 17BDA Imperial SatBOX HD_GB_UES.in17 17 04.04.2008 10:00:57 Uhr04.04.2008 10:00:57 Uhr
16Installation Guide
GB
Search Program:
• If you select Search Satellite button (green key), the searching window will pop up.
System will search all TV and Radio programs under this satellite.
• After searching, press [OK] key to view the searched programs, or press [EXIT] key
to return to Antenna Setup window.
USALS Setup Menu
• If you select USALS Setup Menu button
(blue key), the USALS Setup Menu will
pop up. Through this menu, you can
position your antenna correctly.
• Satellite: The satellite is the same
satellite as Antenna item in Antenna
Setup window. In case the location of the
satellite is changed, you can reset the new
location.
• Your longitude and Your latitude: Enter
the value of the longitude and the latitude
of your location.
• If you enter the correct value of your position, place your cursor to the Go To Sat
Position button. Once [OK] key is pressed on this button, system will position your
antenna to the satellite automatically. Please in patience to wait the process.
• If you want to restore the original position of the antenna, please select Go To 0 but-
ton and press [OK] key. Please in patience to wait the process.
• After setting all necessaries, please [EXIT] to fi nish antenna setup menu. The mes-
sage of “Are you sure to change the confi guration of Antenna setup?” will be
displayed. Please select [OK] button on the screen and then wait for saving a data.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in16 16BDA Imperial SatBOX HD_GB_UES.in16 16 04.04.2008 10:00:58 Uhr04.04.2008 10:00:58 Uhr
15 DVB-S Receiver
GB
Antenna Setup-2) USALS
• Antenna: You can select maximum 16
antenna with the combination switches.
• Type: Select your antenna type to be fi xed.
• Satellite: Select satellite you want.
• LNB Type: Select your LNB type. If you
have universal LNB, select Univ.
• LNB Freq.: Enter the proper LNB frequen-
cy referring to your LNB using numeric
key on the RCU.
If you have a dual LNB, enter the proper value in the both of value box.
• Switches (0/12 Volt, 22KHz Tone, DiSEqC): You can select the switches with which
you want to confi gure the antenna.
• Transponder: Select the transponder you want.
East, West Limit:
• If you select Limit Setup button, Limit Setup menu will pop up.
• Press [E] key on the RCU continuously reaches to the easternmost point and then
press [OK] key on the RCU.
• The message of “Would you like to set East limit of DiSEqC motor?” will be dis-
played for your confi rmation.
• Please cursor on the [OK] button on the screen and press [OK] key on the RCU to
confi rm the East limit. To set West limit, take the same steps as East limit.
Reset DiSEqC limit:
• If you want to reset the East limit or West limit, place a cursor on Reset DiSEqC Limit
button and then press [OK] key on the RCU.
• The message of “Would you like to reset limit for DiSEqC positioner?” will be dis-
played for your confi rmation.
• Select [OK] button by pressing [OK] key on the RCU.
• The cursor will move to the East limit button so that you can reset the limit. After
that, please reset West limit same as before.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in15 15BDA Imperial SatBOX HD_GB_UES.in15 15 04.04.2008 10:00:59 Uhr04.04.2008 10:00:59 Uhr
14Installation Guide
GB
Reset DiSEqC limit:
• If you want to reset the East limit or West
limit, place a cursor on Reset DiSEqC
Limit button and then press [OK] key on
the RCU.
• The message of “Would you like to reset
limit for DiSEqC positioner?” will be
displayed for your confi rmation.
• Select [OK] button by pressing [OK] key
on the RCU.
• The cursor will move to the East limit button so that you can reset the limit. After
that, please reset West limit same as before.
Search Programs:
• If you select Search Satellite button
(green key), the searching window will pop
up. System will search all TV and Radio
programs under this satellite.
• After searching, press [OK] key to view
the searched programs, or press [EXIT]
key to return to Antenna Setup window.
• After setting all necessaries, please
[EXIT] to fi nish antenna setup menu.
• The message of “Are you sure to change the confi guration of Antenna setup?” will
be displayed.
• Please select [OK] button on the screen and then wait for saving a data.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in14 14BDA Imperial SatBOX HD_GB_UES.in14 14 04.04.2008 10:00:59 Uhr04.04.2008 10:00:59 Uhr
13 DVB-S Receiver
GB
Antenna Setup-1) DiSEqC 1.2
• Antenna: You can select maximum 16
antennas with the combination switches.
• Type: Select your antenna type to be DiS-
EqC1.2.
• Satellite: Select fi rst satellite you want.
• LNB Type: Select your LNB type. If you
have universal LNB, select Univ.
• LNB Freq.: Enter the proper LNB frequen-
cy referring to your LNB using numeric
key on the RCU or use the dropdown list
displayed by pressing [OK] key. If you have
a dual LNB, enter the proper value in the
both of value box.
• Switches (0/12 Volt, 22KHz Tone,
DiSEqC): You can select the switches with
which you want to confi gure the antenna.
• Transponder: Select fi rst transponder you
want.
East, West Limit:
• If you select Limit Setup button (yellow
key), Limit Setup menu will pop up.
• Press key on the RCU continuously
reaches to the easternmost point and
then press [OK] key on the RCU.
• The message of “Would you like to set
East limit of DiSEqC motor?” will be
displayed for your confi rmation.
• Please place cursor on the [OK] button
on the screen and press [OK] key on the
RCU to confi rm the East limit.
• To set West limit, take the same steps as
East limit.
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in13 13BDA Imperial SatBOX HD_GB_UES.in13 13 04.04.2008 10:01:00 Uhr04.04.2008 10:01:00 Uhr
12Installation Guide
GB
• Once you properly installed and connected cables of the receiver, the menu will be
displayed.
• This menu consists of 6 major main
menus as follow:
• Manager
• Guide (EPG)
• Timer
• Installation
• Game
• CA SYSTEM
• During the installation the [OK] key confi rms a selection and [LIST] key shows Down
List Box if the column has mark. You can also use the numeric keys on the RCU to
enter numeric value.
• Use the [PR+/PR-] key to move upwards and downwards from one line to another
line and use key to move from main menu to sub menu and move from left
side to right side or versa.
• Meantime, you want to escape the menu system, please press [EXIT] key on the RCU.
• This menu consists of 5 major sub-menus
as below.
• Antenna Setup
• Channel Search
• System Setting
• Parental Lock
• Factory Default
MENU INFORMATION
BDA Imperial SatBOX HD_GB_UES.in12 12BDA Imperial SatBOX HD_GB_UES.in12 12 04.04.2008 10:01:01 Uhr04.04.2008 10:01:01 Uhr
11 DVB-S Receiver
GB
INSTALLATION
Connecting to another satellite receiver
Satellite
Dish
Another
SVR
DSR
TV
BDA Imperial SatBOX HD_GB_UES.in11 11BDA Imperial SatBOX HD_GB_UES.in11 11 04.04.2008 10:01:02 Uhr04.04.2008 10:01:02 Uhr
10Installation Guide
GB
INSTALLATION
Connecting to TV & VCR using SCART support
Connecting to Antenna & TV
VCR
IN
Cable or
OFF-Air Antenna
Satellite
Dish
DSR
TV
Antenna DSR
BDA Imperial SatBOX HD_GB_UES.in10 10BDA Imperial SatBOX HD_GB_UES.in10 10 04.04.2008 10:01:02 Uhr04.04.2008 10:01:02 Uhr
9 DVB-S Receiver
GB
GENERAL INFORMATION
RearPanel
Output to connect another satellite receiver
Input to connect the cable from satellite dish
SCART output to connect your video
recorder or DVD player
Left/Right analogue audio outputs and digital
output to connect your receiver to your TV
Connect to PC for S/W
upgrade
Socket to connect
the mains cord
Socket to connect the Internet
Connect to USB device
SCART output used to connect your TVset or a video
projector
Digital audio output to connect your video receiver to
your digital audio equipment using an optical cable
(not supplied).
HDMI-OUT socked used to connect your
TV set HDMI-OUT input
Output used to connect your
TV set or video projector
YPbPr or component inputs
Main
ON/OFF
switch
BDA Imperial SatBOX HD_GB_UES.in9 9BDA Imperial SatBOX HD_GB_UES.in9 9 04.04.2008 10:01:03 Uhr04.04.2008 10:01:03 Uhr
8Installation Guide
GB
GENERAL INFORMATION
Front Panel
Standby
Return to the previous menu on the menu screen or
escape the desired value.
Executes the selected item in the menu screen or
enters the desired value in any input mode.
Press this key one time to run menu on screen.
in live mode, increasing the volume.
in live mode, decreasing the volume.
in live mode, changing to the next channel.
in live mode, changing to the previous channel.
BDA Imperial SatBOX HD_GB_UES.in8 8BDA Imperial SatBOX HD_GB_UES.in8 8 04.04.2008 10:01:05 Uhr04.04.2008 10:01:05 Uhr
7 DVB-S Receiver
GB
ALLGEMEINE INFORMATIONEN
RCU
Display the menu on
screen
When watching a channel,
mute the sound
Adjust the volume
Turns power ON/OFF of
the DSR
Switches between TV
and AV modes
Returns to the
previous menu on the
menu screen or escape
from the menu
Enter number of the re-
quired menu item or select
a channel number to watch
Calls up the EPG
(Electronic Program
Guide)
Switches to teletext or
subtitle mode
Changes the HD-Format
Switches directly to
Premiere channels
Chooses audio mode
Switches back to
previous channel
Switches to nine-
picture mode
Motor settings
Selects the different
audio modes
Executes the desired
item on the menu screen
or, in any input mode,
enters the desired value
Display the favorite
channel list
Moves up/down a page
in the channel list
Changes to the next
higher or lower channel,
or other item on a menu
list
Moves left or right in a
menu window
Switches between TV
and Radio mode
Shows information of
the current channel
BDA Imperial SatBOX HD_GB_UES.in7 7BDA Imperial SatBOX HD_GB_UES.in7 7 04.04.2008 10:01:06 Uhr04.04.2008 10:01:06 Uhr
6Installation Guide
GB
GENERAL INFORMATION
General Operation
• Throughout this manual you will notice that the everyday operation of the receiver
is based on a series of user friendly on screen display and menus. These menus will
help you getting the most from your receiver, guiding you through installation, channel
organizing, viewing and many other functions.
• All function can be carried out using the buttons on the RCU, and some of the
functions can also be carried out using the buttons on the front panel.
• The receiver is easy to use, always at your command and adaptable for future ad-
vances.
• Please be aware that new software may change the functionality of the receiver.
• Should you experience any dif. culties with the operation of your receiver, please
consult the relevant section of this manual, including the problem shooting, or
alternatively call your dealer or a customer service adviser.
Fernbedienung Batterien
BDA Imperial SatBOX HD_GB_UES.in6 6BDA Imperial SatBOX HD_GB_UES.in6 6 04.04.2008 10:01:07 Uhr04.04.2008 10:01:07 Uhr
5 DVB-S Receiver
GB
GENERAL INFORMATION
For Your Safety
Do not expose the receiver under the sunlight.
Keep it away from the heat source.
Do not block ventilation holes of the
Receiver so that air can circulate freely.
When an abnormal phenomenon occurs,
you should cut off the power immediately.
Switch the receiver off whenever it remains
out of service for an extended period.
Do not touch the receiver during thunder,
since that might create electric-shock
hazards.
Be sure that the Receiver is turned off and
disconnect the AC power cord before
cleaning the Receiver surface. If the
surface is dirty, wipe clean with a cloth
which has been dipped in a weak soap-and-
watersolution and wrung out thoroughly,
and then wipe again with a dry cloth.
To avoid electric-shock hazards, do not
open the cabinet, refer servicing to quali-
fi ed personnel, only.
Keep the receiver away from fl ower vases,
tubs, sinks, etc., in order to avoid damaging
the equipment.
BDA Imperial SatBOX HD_GB_UES.in5 5BDA Imperial SatBOX HD_GB_UES.in5 5 04.04.2008 10:01:08 Uhr04.04.2008 10:01:08 Uhr
4Installation Guide
GB
GENERAL INFORMATION
A digital terrestrial receiver allows you to view a variety of programs provided through
antenna. This user‘s guide covers the installation of the receiver and the necessary
steps to implement various features. This also explains special features available only
in this receiver in detail, which ensures easy operation. Information confi rmed in this
document is subject to change. We reserve of complete functions the right, without
prior notice, to make changes in product design or performances in line with progress in
engineering and technology.
Main Features
• MPEG 2/4 digital & fully DVB-S 2 (SD/HD) compliant
• Slot to the admission of 2 CI (Pay-TV)
• Alphanumeric display (VF-Display 13-digit)
• 1 Smart-Card reader for CONAX coded programs
• 7.000 channels TV and Radio programmable
• Comfortable pre-programmed program list
• 32 different favourite group’s selection
• 10 programmable timers
• Multi-language menu
• Teletext support and subtitle support (OSD)
• Time and date indication in the standby mode
• EPG now/next for 7-days
• Software update over Satellite (OTA), USB and RS 232 interface
• Parental control for channels and menu
• DiSEqC 1.0 and 1.2
• Picture in Graphics (PIG)
• Picture formats: 4:3 LetterBox, PanScan/16:9, Automatic change-over 16:9/4:3
Connections:
• HDMI digital output v.1.1 for the formats 576i, 576p, 720p und 1080i
• 2 Scart connections for TV and VCR/DVD
• YUV Componenten (Y/Pb/Pr) Video Cinch Output
• Optical and electrical digital output (S/PDIF) for Dolby Digital
• 2 x Cinch Audio (R/L)
• Loop-through tuner to connect a second receiver
• RJ-45 Ethernet socket
• RS 232 Interface
• USB 2.0 Interface
• Power Switch
• HDMI-Cable
• Remote control (incl. batteries)
BDA Imperial SatBOX HD_GB_UES.in4 4BDA Imperial SatBOX HD_GB_UES.in4 4 04.04.2008 10:01:09 Uhr04.04.2008 10:01:09 Uhr
3 DVB-S Receiver
GB
CONTENTS
EPG (Electronic Program Guide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
GAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
ANTENNA DIRECTION HELP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
CONDITIONAL ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
SOFTWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
TECHNICAL SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
BDA Imperial SatBOX HD_GB_UES.in3 3BDA Imperial SatBOX HD_GB_UES.in3 3 04.04.2008 10:01:09 Uhr04.04.2008 10:01:09 Uhr
… 42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Digitalbox IMPERIAL SatBOX HD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Digitalbox IMPERIAL SatBOX HD in de taal/talen: Engels als bijlage per email.

De handleiding is 2,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Digitalbox IMPERIAL SatBOX HD

Digitalbox IMPERIAL SatBOX HD Aanvulling / aanpassing - Deutsch - 7 pagina's

Digitalbox IMPERIAL SatBOX HD Gebruiksaanwijzing - Deutsch - 42 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info