546144
14
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
ENGLISH
12
Always mount your saw firmly to prevent movement. To enhance
the portability, the tool can be mounted to a piece of 12.5 mm or
thicker plywood which can then be clamped to your work support
or moved to other job sites and reclamped.
When mounting your saw to a piece of plywood, make sure that
the mounting screws do not protrude from the bottom of the wood.
The plywood must sit flush on the work support. When clamping
the saw to any work surface, clamp only on the clamping bosses
where the mounting screw holes are located. Clamping at any
other point will interfere with the proper operation of the saw.
To prevent binding and inaccuracy, be sure the mounting surface is
not warped or otherwise uneven. If the saw rocks on the surface,
place a thin piece of material under one saw foot until the saw is
firm on the mounting surface.
ASSEMBLY
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An accidental start-
up can cause injury.
MOUNTING THE SAW BLADE (FIG. E1–E5)
Never depress the spindle lock button while the blade is
under power or coasting.
Do not cut light alloy and ferrous metal (containing iron or
steel) or masonry or fibre cement product with this mitre
saw.
Depress the head lock up release lever (17) to release
the lower guard (2), then raise the lower guard as far as
possible.
1. With the lower guard held in the raised position by the guard
bracket screw (43), depress the spindle lock button (16) with one
hand, then use the supplied blade spanner (26) in the other hand to
loosen the left-hand threaded blade locking screw (45) by turning
clockwise.
WARNING! To use the spindle lock, press the button as
shown and rotate the spindle by hand until you feel the lock
engage.
Continue to hold the lock button in to keep the spindle from
turning.
2. Remove the blade locking screw (45) and the outside arbor
collar 46).
3. Install the saw blade (47) onto the shoulder (48) provided on the
inside arbor collar (49), making sure that the teeth at the bottom
edge of the blade are pointing toward the back of the saw (away
from the operator).
4. Replace the outer arbor collar (46).
5. Tighten the blade locking screw (45) carefully by turning counter-
clockwise while holding the spindle lock engaged with your other
hand.
WARNING! Be aware the saw blade shall be replaced in
the described way only. Only use saw blades as specified
under Technical Data: Cat. no.: DT4320 is suggested.
Adjustment
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An accidental start-
up can cause injury.
Your mitre saw was accurately adjusted at the factory. If readjustment
due to shipping and handling or any other reason is required, follow the
steps below to adjust your saw. Once made, these adjustments should
remain accurate.
CHECKING AND ADJUSTING THE BLADE TO THE FENCE (FIG. F1–F4)
Release the mitre lever (4) and depress the mitre latch (5) to release
the mitre arm (50).
Swing the mitre arm until the latch locates it at the 0° mitre position.
Do not tighten the lever.
Pull down the head until the blade just enters the saw kerf (51).
Place a square (52) against the left side (3) of the fence and blade
(47) (fig. F3).
WARNING: Do not touch the tips of the blade teeth with
the square.
If adjustment is required, proceed as follows:
Loosen the screws (53) and move the scale/mitre arm assembly left
or right until the blade is at 90° to the fence as measured with the
square.
Retighten the screws (53). Pay no attention to the reading of the
mitre pointer at this point.
ADJUSTING THE MITRE POINTER (FIG. F1, F2 & G)
Release the mitre lever (4) and depress the mitre latch (5) to release
the mitre arm (50).
Move the mitre arm to set the mitre pointer (54) to the zero
position, as shown in fig. G.
With the mitre lever loose, allow the mitre latch to snap into place
as you rotate the mitre arm past zero.
Observe the pointer (54) and mitre scale (6). If the pointer does not
indicate exactly zero, loosen the screw (55), move the pointer to
read 0° and tighten the screw.
MITRE LOCK/DETENT ROD ADJUSTMENT (FIG. H)
If the base of the saw can be moved while the mitre lever (4) is locked,
the mitre lock/detent rod (56) must be adjusted.
Unlock the mitre lever (4).
Fully tighten the mitre lock/detent rod (56) using a screwdriver (57).
Then loosen the rod a quarter of a turn.
Check that the table does not move when the lever (4) is locked at
a random (not preset) angle.
CHECKING AND ADJUSTING THE BLADE TO THE TABLE (FIG. I1–I4)
Loosen the bevel clamp handle (11).
Press the saw head to the right to ensure it is fully vertical and
tighten the bevel clamp handle.
Pull down the head until the blade just enters the saw kerf (51).
Place a set square (52) on the table and up against the blade (47)
(fig. I2).
WARNING: Do not touch the tips of the blade teeth with
the square.
If adjustment is required, proceed as follows:
Loosen the bevel clamp handle (11) and turn the vertical position
adjustment stop screw (28) in or out until the blade is at 90° to the
table as measured with the square.
If the bevel pointer (58) does not indicate zero on the bevel scale
(10), loosen the screw (59) that secures the pointer and move the
pointer as necessary.
ADJUSTING THE FENCE (FIG. J1, J2)
The upper part of the left side of the fence can be adjusted to the left to
provide clearance, allowing the saw to bevel to a full 48° left. To adjust
the fence (3):
Loosen the plastic knob (29) and slide the fence to the left.
Make a dry run with the saw switched off and check for clearance.
Adjust the fence to be as close to the blade as practical to provide
maximum workpiece support, without interfering with the up and
down movement of the arm.
Tighten the knob securely.
WARNING: The guide groove (60) can become clogged
with sawdust. Use a stick or some low pressure air to clear
the guide groove.
The moveable part of the right side of the fence can be adjusted to
provide maximum support of the workpiece near the blade, while
allowing the saw to bevel to a full 45° left. The sliding distance is limited
by stops in both directions.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW712 T 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW712 T 5 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info