546144
18
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
ENGLISH
16
Cleaning
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine that it will
operate properly. Ensure that chips, dust or workpiece particle cannot
lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow the
instructions given in section Mounting the Saw Blade. Remove the
jammed parts and reassemble the saw blade.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
CLEANING AND MAINTAINING THE KERF PLATE (FIG. U)
Regularly clean the area below the kerf plate.If the kerf plate is worn it
must be replaced.
Remove the screws (67) holding the kerf plate (31).
Remove the kerf plate and clean the area below.
Re-install the parts of the kerf plate and the screws.
Tighten the screws hand-tight.
To adjust the kerf plate, proceed as follows:
Pull down the head until the blade just enters the saw kerf.
Adjust each part of the kerf plate to fit closely to the teeth of the
blade.
Tighten the screws.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
EWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DEWALT, recommended
accessories should be used with this product.
SAW BLADES
ALWAYS use 216mm saw blades with 30mm arbour holes. Blade
speed rating must be at least 5500 RPM. Never use a smaller or
greater blade diameter. It will not be guarded properly.
BLADE DESCRIPTIONS
APPLICATION DIAMETER TEETH
Construction Saw Blades (for all purpose cutting)
General Purpose 216mm 48
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts 216mm 60
Consult your dealer for further information on the appropriate
accessories.
Protecting the Environment
Separate collection. This product must not be disposed of with
normal household waste.
Should you find one day that your D
EWALT product needs replacement,
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of
recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
D
EWALT provides a facility for the collection and recycling of DEWALT
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D
EWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT repair agents and
full details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
GUARANTEE
DEWALT is confident of the quality of its products and offers an
outstanding guarantee for professional users of the product. This
guarantee statement is in addition to and in no way prejudices
your contractual rights as a professional user or your statutory
rights as a private non-professional user. The guarantee is valid
within the territories of the Member States of the European Union
and the European Free Trade Area.
30 DAY NO RISK SATISFACTION GUARANTEE
If you are not completely satisfied with the performance of your
D
EWALT tool, simply return it within 30 days, complete with all
original components, as purchased, to the point of purchase, for
a full refund or exchange. The product must have been subject to
fair wear and tear and proof of purchase must be produced.
ONE YEAR FREE SERVICE CONTRACT
If you need maintenance or service for your D
EWALT tool, in
the 12 months following purchase, you are entitled to one
service free of charge. It will be undertaken free of charge at an
authorised DEWALT repair agent. Proof of purchase must be
produced. Includes labour. Excludes accessories and spare parts
unless failed under warranty.
ONE YEAR FULL WARRANTY
If your D
EWALT product becomes defective due to faulty
materials or workmanship within 12 months from the date of
purchase, D
EWALT guarantees to replace all defective parts free
of charge or – at our discretion – replace the unit free of charge
provided that:
The product has not been misused;
The product has been subject to fair wear and tear;
Repairs have not been attempted by unauthorised persons;
Proof of purchase is produced;
The product is returned complete with all original
components.
If you wish to make a claim, contact your seller or check the
location of your nearest authorised D
EWALT repair agent in the
D
EWALT catalogue or contact your DEWALT office at the address
indicated in this manual. A list of authorised DEWALT repair
agents and full details of our after-sales service is available on the
Internet at: www.2helpU.com.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW712 T 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW712 T 5 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info