544677
25
Verklein
Vergroot
Pagina terug
1/91
Pagina verder
20
ENGLISH
en - 6
Screw the side handle (8) into the clamp wheel
and tighten it.
Rotate the side handle mounting assembly to the
desired position. For drilling horizontally with a
heavy drill bit, place the side handle at an angle of
approx. 20° (refer to fig. E) for optimum control.
Lock the side handle mounting assembly in place
by tightening the clamp wheel (9).
Mounting in rear position (fig. F)
The rear position is particularly useful when drilling
overhead or down into a floor. Refer to fig. G.
Unscrew the side handle (8) and remove it from
the front position. Leave the side handle
mounting assembly in front position so that the
depth adjustment rod can still be used.
Screw the side handle directly into one of the rear
side handle positions (10) on either side of the tool.
Setting the drilling depth (fig. H)
Insert the required drill bit.
Loosen the clamp nut (21) and fit the depth
adjustment rod (11) through the hole in the side
handle clamp.
Push the drill bit into a surface at a right angle and
adjust the depth adjustment rod (11) as shown.
Tighten the clamp nut (21).
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and
wiring.
Apply only a gentle pressure to the tool
(approx. 20 kg). Excessive force does
not speed up drilling or chiselling but
decreases tool performance and may
shorten tool life.
Drilling with a solid bit (fig. A)
Set the electronic speed and impact control dial
(2) (DW541/DW545).
Set the mode selector lever (5) to the hammer
drilling position.
Insert the appropriate drill bit.
Fit and adjust the side handle (8).
If necessary, set the drilling depth.
Mark the spot where the hole is to be drilled.
Place the drill bit on the spot and press the ON/
OFF-switch (1).
To stop the tool, release the ON/OFF-switch (1).
Always switch OFF the tool when work is finished
and before unplugging.
Drilling with a core bit (fig. A)
Turn the electronic speed and impact control dial
(2) (DW541/DW545) to medium or high speed
position.
Set the mode selector lever (5) to the hammer
drilling position.
Fit and adjust the side handle (8).
Insert the appropriate core bit.
Assemble the centerdrill into the core bit.
Place the centerdrill on the spot and press the
ON/OFF-switch (1). Drill until the core penetrates
into the concrete approx. 1 cm.
Stop drilling and remove the centerdrill. Place the
core bit back into the hole and continue drilling.
When drilling through a structure thicker than the
depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals. To avoid unwanted breaking
away of concrete around the hole, first drill a hole
the diameter of the centerdrill completely through
the structure. Then drill the cored hole halfway
from each side.
To stop the tool, proceed as described above.
Chipping and chiselling (fig. A)
Set the electronic speed and impact control dial
(2) (DW541/DW545).
Set the mode selector lever (5) to the hammering
only with spindle lock position.
Insert the appropriate chisel and rotate it by hand
to lock it into one of 8 positions.
Fit and adjust the side handle (8).
Press the ON/OFF-switch (1) and start working.
To stop the tool, proceed as described above.
Various types of SDS-max
®
drill bits and chisels are
available as an option.
Consult your dealer for further information on the
appropriate accessories.
Maintenance (fig. A)
Your DEWALT Power Tool has been designed to
operate over a long period of time with a minimum of
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW540 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW540 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info