544677
24
Verklein
Vergroot
Pagina terug
1/91
Pagina verder
19
ENGLISH
en - 5
Hammering only with spindle lock:
impacting only - for light chipping,
chiselling and demolition applications.
SDS-max
®
chisels can be locked into 8
different positions (also refer to fig. C):
Rotate the mode selector (5) until it covers the
safety lock (16).
Lock the chisel in the required position.
Rotate the mode selector (5) until it points to the
-symbol.
In this mode the Rotary Hammer can also be
used as a lever to free a jammed drill bit.
Select the required operating mode by rotating
the mode selector lever (5) over the safety lock
(16) until it points to the symbol.
Inserting and removing SDS-max
®
accessories
(fig. C)
These models use SDS-max
®
drill bits and chisels
(refer to the inset in fig. C for a cross-section of an
SDS-max
®
bit shank).
Unplug the tool.
Insert the bit shank into the tool holder locking
sleeve (6) and turn the bit slightly until the sleeve
snaps in position.
Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
To remove a bit pull back the tool holder locking
sleeve (6) and pull the bit out of the tool holder.
Assembling and fitting the side handle
The side handle (8) can be mounted in front or in
rear position on either side of the Rotary Hammer to
suit both RH- and LH-users.
Always operate the Rotary Hammer with
the side handle properly assembled.
Mounting in front position (fig. D)
Unscrew the side handle (8) and disassemble the
side handle clamp (20).
Snap the steel ring (17) over the collar (7) behind
the tool holder (6). Squeeze both ends together,
mount the bush (18) and insert the pin (19).
Place the side handle clamp (20) and screw on
the clamp wheel (9). Do not tighten.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
220/240 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
DW541/DW545 - Setting the electronic speed
and impact control dial (fig. B)
Turn the dial (2) to the desired level. The higher
the number, the greater the speed and impact
energy. With dial settings from 1 (low) to 7 (full
power) the tool is extremely versatile and
adaptable for many different applications. The
required setting is a matter of experience.
E.g. when using smaller diameter bits or when
drilling into ceramic or brittle materials, set the
dial to position 1 (low).
Selecting the operating mode (fig. B)
Your Rotary Hammer can be used in two operating
modes:
Hammer drilling:
simultaneous rotating and impacting - for
all concrete and masonry drilling
operations.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW540 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW540 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info