546638
23
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
23
ENGLISH
Tighten the fixing screw (13) with the Allen key (9).
Repeat this procedure for the other side handle.
Always operate the tool with the side
handles properly assembled.
Replacing the saw blades
Removing the saw blades (fig. C)
Turn the tool upside down and remove the saw
blade guard (7).
Loosen both saw blade fixing screws (8) with the
Allen key (9) until a click is heard.
Unlock the top cover (17) by pressing the spring.
Tilt back the top cover and pull the saw blades
out of the bar (6).
Fitting the saw blades (fig. D)
Slide one saw blade into the bar (6) until its
slotted hole (16) is at approx. 5 cm from the top
cover (17).
Insert the back of the saw blade into the housing
(10) until the threaded hole (14) lodges in the
required mounting position.
Repeat this procedure for the other saw blade.
Tilt the top cover (17) back in position and lock it.
Using a piece of wood push on the toothed side
of the saw blades to make sure that they are
exactly parallel to the bar (6).
Tighten both saw blade fixing screws (8) securely
by pressing and turning simultaneously with the
short end of the Allen key (9).
Before operation let the saw blades run
freely for approx. 20 s.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Ensure the material to be sawn is
secured in place.
Apply only a gentle pressure to the tool
and do not exert side pressure on the
saw blade.
Avoid overloading.
Prior to operation (fig. A)
Remove the saw blade guard (7).
Mount the appropriate type of saw blade.
Check that the tool is running properly and can
perform all its functions. Make sure that the bar (6)
is still straight and the saw blades (5) and the
housing (10) are undamaged.
Switching on and off (fig. A)
For safety reasons the on/off-switch (1) is equipped
with a lock-off button (2).
Press the lock-off button (2) to unlock the tool.
To run the tool, press the on/off-switch (1).
As soon as the on/off-switch is released the lock-
off switch is automatically activated to prevent
unintended starting.
Always switch off the tool before unplugging.
Sawing (fig. A, E & F)
Clamp the workpiece on one side only to prevent
the bar from jamming in the workpiece. Should
this happen, ease open the cut with wedges to
relieve the strain on the blade. Do not try to
wrench the saw free.
Hold the tool by the front (3) and the side handle (4)
to guide it properly.
Do not use the saw for cutting curves or pockets.
Make sure the bar end protrudes from the
workpiece.
For long, straight cuts first draw a line on the
workpiece and follow the line.
Make downward cuts only. Avoid cutting earth as
this will blunt the saw blades very quickly.
When using a saw horse always cut on the
outside of the saw horse arms.
To increase performance and lifetime of the saw
blades regularly apply oil to the blades and in the
oil holes (11) (every 15-30 min.).
Regularly check the saw blade fixing screws (8).
Sawing in cellular concrete and thermal building
blocks (fig. A)
Cellular concrete and thermal building
blocks contain lime and quartz sand.
To guarantee optimum performance,
the saw blades, the bar and the saw
blade guide slot (12) must be thoroughly
cleaned after use.
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW394 T 4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW394 T 4 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info