446564
26
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
26
ENGLISH
!
Always ensure that the cable clamp is
correctly and securely tted to the
sheath of the cable.
Assembly and adjustment
@
Prior to assembly and adjustment
always unplug the tool.
Mounting and removing the guard ( g. B)
Place the angle grinder on a table, spindle up.
Align the lugs (7) with the notches (8).
Press the guard (5) down and rotate it to the
required position.
Securely tighten the screw (9).
To remove the guard, slacken the screw.
@
Never use the tool without the guard in
place.
Fitting and removing a grinding or cutting disc
( g. C1 & C2)
Place the tool on a table, guard up.
Fit the inner ange (10) correctly onto the
spindle (11) ( g. C1).
Place the disc (12) on the ange (10).
When tting a disc with a depressed centre,
make sure that the depressed centre (13) is
facing the ange (10).
Screw the outer ange (14) onto the spindle (11)
( g. C2):
- the ring on the ange (14) must face towards
the disc when tting a grinding disc (A);
- the ring on the ange (14) must face away
from the disc when tting a cutting disc (B).
Press the spindle lock (4) and rotate the spindle
(11) until it locks in position.
Tighten the ange (14) with the two-pin spanner
supplied.
Release the spindle lock.
To remove the disc, loosen the ange (14) with
the two-pin spanner.
@
Do not use a damaged disc.
Fitting a wire cup brush
Screw the wire cup brush directly onto the
spindle without the use of the spacer and
threaded ange.
Mounting the side handle ( g. D)
Screw the side handle (6) tightly into one of the
holes (15) on either side of the gear case.
Holding the tool ( g. E)
Hold the tool as shown.
@
For your own safety, always use the
tool with both hands.
Always wear regular working gloves
while operating this tool.
Warning: The gear case becomes very
hot during use.
Instructions for use
@
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the tool.
Do not exert side pressure on the
grinding wheel or cutting disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
Be sure the inner and outer ange are mounted
correctly.
Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and
the tool.
Switching on and off ( g. A)
The on/off switch is equipped with an unlocking
switch or a locking switch for continuous operation.
On/off switch (1) with locking switch (2)
To run the tool, depress the unlocking switch (3)
and subsequently operate the on/off switch (1).
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D28491 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D28491 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt D28491

DeWalt D28491 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 176 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info