446564
24
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
24
ENGLISH
&
Do not cut or grind light metal with a
magnesium content exceeding 80%
since this type of metal is ammable.
Do not use any accessories other than bre
reinforced grinding and cutting discs.
Use only plain or depressed-centre grinding
and cutting discs.
Use the grinding and cutting discs recommended
by the manufacturer only.
The max. allowable speed of the grinding wheel
or cutting disc, or any other suitable accessory,
must always be equal to or greater than the
no-load speed of the tool speci ed on the
nameplate.
Do not cut workpieces requiring a maximum
depth of cut exceeding that of the cutting disc.
Do not use grinding and cutting discs that do
not conform to the dimensions stated in the
technical data. Do not use any spacers to make
a disc t onto the spindle. Do not separate
reducing bushings or adapters to adapt large-
hole abrasive wheels.
Inspect grinding and cutting discs before each
use. Do not use chipped, cracked or otherwise
defective discs.
If provided, ensure that blotters are used when
the disc is tted onto the spindle.
When applying a threaded hole disc, ensure that
the thread is long enough to accept the spindle.
Ensure that the grinding or cutting disc is
mounted correctly before use.
Let the tool run at no-load in a safe position for
at least 30 seconds. If there is a considerable
vibration or if any other defect occurs, stop the
tool and check it to determine the cause.
Do not operate this tool without the guard in place.
Check that the workpiece is properly supported.
Do not operate the tool near ammable liquids,
gases or dust. Sparks or hot chips from cutting
or arcing motor brushes may ignite combustible
materials.
Do not operate the tool while standing in line
with the disc. Keep other persons away from
the work area.
Do not use cutting discs for side grinding.
Do not operate the spindle lock while the tool is
running.
Beware that after switching off the tool the
wheel continues to rotate for a short period.
Always store grinding and cutting discs
in a dry place.
Labels on tool
The following pictographs are shown on the tool:
+
Read the instruction manual before use
F
Wear safety glasses
f
Wear ear protection
Package contents
The package contains:
1 Angle grinder
1 Guard
1 Side handle
1 Flange set
1 Two-pin spanner
1 Kitbox (K-models only)
1 Instruction manual
1 Exploded drawing
Check for damage to the tool, parts or
accessories which may have occurred during
transport.
Take the time to thoroughly read and
understand this manual prior to operation.
Description ( g. A)
Your angle grinder D28490/D28491/D28492(K)/
D28493 has been designed for professional
grinding and cutting applications.
1 On/off switch
2 Locking switch (not for France)
3 Unlocking switch
4 Spindle lock
5 Guard
6 Side handle
Electrical safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D28491 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D28491 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt D28491

DeWalt D28491 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 176 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info