546219
50
Verklein
Vergroot
Pagina terug
1/172
Pagina verder
48
ENGLISH
Transporting (fi g. X)
WARNING: Always transport the machine in saw bench mode
with the upper blade guard fitted.
The castor wheels provide an easier transport of the machine.
Put the machine on the right base side.
Fold the rear legs into the base
Fold the front legs out of the base
Turn the machine straight up.
Lift the machine by the front legs up to the wheels are in contact with
the floor.
WARNING: When carrying the machine, always seek
assistance.
MAINTENANCE
Your DEWALT power tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
Lubrication
The bearings of the motor are pre-lubricated and watertight.
Slightly oil the rotating table bearing surface where it slides on the lip of
the fi xed table at regular intervals.
Periodically lubricate the depth of cut screwthread.
Clean the parts subject to accumulation of sawdust and chips
periodically with a dry brush.
Cam adjustment (fi g. Y1 - Y3)
To take out the clearance between the two tables, proceed as follows:
Rotate the machine into saw bench mode.
Remove the screws (138) and the retainer plate (139).
Loosen the screw (140) of the adjustment cam (141).
Rotate the adjustment cam using a pair of needle nose pliers.
Hold the adjustment cam with the pliers and tighten the screw.
Replace the retainer plate and tighten the screws.
Rotate the machine into mitre saw mode. Check the force that is
needed to mitre the saw. Repeat the above steps if the force needed is
too high.
Cleaning
Before use, carefully check the upper blade guard, movable lower blade
guard as well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or workpiece particle cannot lead to
blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and guards
disconnect the machine from the power supply and follow the instructions
given in section Mounting the Saw Blade. Remove the jammed parts and
reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing with dry
air as often as dirt is seen collecting in and around the air vents.
Wear approved eye protection and approved dust mask when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals
may weaken the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool into a
liquid.
WARNING: To reduce the risk of injury, regularly clean the
table top.
WARNING: To reduce the risk of injury, regularly clean the
dust collection system.
Optional Accessories
WARNING: Since accessories, other than those offered by
DEWALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the
risk of injury, only D
EWALT, recommended accessories should
be used with this product.
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. This product must not be disposed of with
normal household waste.
Should you find one day that your D
EWALT product needs replacement, or
if it is of no further use to you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of recycled
materials helps prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of electrical products
from the household, at municipal waste sites or by the retailer when you
purchase a new product.
D
EWALT provides a facility for the collection and recycling of DEWALT
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D
EWALT office at the address indicated in this manual.
Alternatively, a list of authorised DEWALT repair agents and full details
of our after-sales service and contacts are available on the Internet at:
www.2helpU.com.
50

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D27107 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D27107 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 15,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info