546219
49
Verklein
Vergroot
Pagina terug
1/172
Pagina verder
47
ENGLISH
- Right side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
Outside corner
- Left side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the right side of the cut.
- Right side
• Top of the moulding against the fence.
• Mitre right.
• Save the right side of the cut.
Sawing in the bench mode
Always use the riving knife.
Always ensure that the riving knife and blade guard are correctly
aligned.
Always ensure that the mitre saw is set and locked in 0° mitre.
WARNING: Do not cut metal in this mode.
Ripping (fi g. U1 & U3)
Set the bevel angle to 0°.
Adjust the saw blade height.
Set the parallel fence to the required distance.
Hold the workpiece fl at on the table and against the fence. Keep the
workpiece approx. 25 mm away from the saw blade.
Keep both hands away from the path of the saw blade.
Switch the machine on and allow the saw blade to reach full speed.
Slowly feed the workpiece underneath the upper blade guard, keeping
it fi rmly pressed against the fence. Allow the teeth to cut, and do not
force the workpiece through the saw blade. The saw blade speed
should be kept constant.
Remember to use the push stick (23) when close to the blade.
After completing the cut, switch the machine off, allow the saw blade
to stop and remove the workpiece.
WARNING: Never push or hold the free or cut-off side of the
workpiece.
WARNING: Always use a push stick when ripping small
workpieces.
Bevel cuts (fi g. U2)
Set the required bevel angle.
Proceed as for ripping.
Cross-cutting (fi g. V1)
Set the bevel angle to 0°.
Adjust the saw blade height.
Set the mitre fence to 0°.
Proceed as for ripping, only use the mitre fence to push the workpiece
through the blade.
Bevel cross-cutting
Set the required bevel angle.
Proceed as for cross-cutting.
Mitre cuts (fi g. V2)
Set the mitre fence to the required angle.
Proceed as for cross-cutting.
Optional attachments
WARNING: Prior to assembling any accessories always unplug
the machine.
Dust extraction kit (fi g. W1 & W2)
WARNING! This machine is provided with two dust extraction
points for use in each mode.
WARNING! Whenever possible, connect a dust extraction
device designed in accordance with the relevant regulations
regarding dust emission.
WARNING! When sawing wood, connect a dust extraction
device designed in accordance with the relevant regulations
regarding dust emission.
Connect a dust collection device designed in accordance with the relevant
regulations. The air velocity of externally connected systems shall be 20m/s
±2 m/s. Velocity to be measured in the connection tube at the point of
connection, with the tool connected but not running.
Connecting - mitre saw position (fi g. W1)
Connect the one end of the fi rst hose to the dust extraction adaptor (13).
Insert the other end of the hose into the middle inlet port of the
manifold (128).
Connect the one end of the other hose to the under-table guard (63).
Insert the other end of the hose into the outer inlet port of the manifold.
Connecting - saw bench position (fi g. W2)
Proceed as for mitre saw position, only connect the hose from the
under-table guard to the saw blade guard (21).
Mitre saw extra support/length stop (fi g. A5)
The extra support and length stop can be mounted on the left-hand side
or on the right-hand side, or with two sets on either side.
Fit the items 31 - 39 onto the two guide rails (32 & 33).
Use the inclinable support (34) for cross-cutting 210 mm wide boards
(15 mm thick).
Roller support table (fi g. A6)
The roller support table (40) is used to support long workpieces. In mitre
saw mode, the roller support table can be mounted on the left-hand side
or on the right-hand side, or with two sets on either side. In saw bench
mode, it can also be mounted in front or at the rear of the saw table.
Side extension table (fi g. A8)
The side extension table (42) increases the distance from the rip fence to
the blade to 600 mm or more, depending on the rod length fi tted to the
machine and the clamped position of the table. The side extension table
must be used in conjunction with guide rails (32) (option). The adjustable
table is equipped with an engraved scale along its front edge and
mounted on a sturdy base which clamps to the guide rods.
Fit the extension table to the right-hand side of the machine for
continuity of the distance scale on both tables.
Sliding table (fi g. A9)
This sliding table (43) allows for board sizes to the left of the blade up to
1200 x 900 mm.
The guide rods are mounted on a sturdy alloy extrusion which is quickly
detachable from the machine and yet fully adjustable is all planes.
The fence incorporates a full length measuring tape for quick positioning
of an adjustable stop and an adjustable support for narrow workpieces.
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D27107 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D27107 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 15,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info