648451
3
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
EN
EN • 3
MANUAL
CONGRATULATIONS
Congratulations on purchasing your new CTEK professional 24V DC/DC switch mode battery
charger, 12V converter and battery equalizer. This charger is part of a range of professional bat-
tery chargers from CTEK SWEDEN AB. It represents the latest technology in battery charging with
charging and analysis in 4 steps with temperature compensation.
Read this User Manual and follow the instructions carefully before using your new charger.
SAFETY
The charger is designed for 24V lead-acid batteries mounted into vehicles.
Do not use the charger for any other purpose
Use safety glasses when connecting or disconnecting a battery.
Battery acid is corrosive. Rinse immediately with water if acid comes into contact with skin
or eyes. Seek medical advice.
Make sure that the cables are not being pinched or in contact with warm surfaces
or sharp edges.
While charging, a battery can emit explosive gases, avoid sparks in the immediate area.
Always provide for proper ventilation during charging.
Avoid covering the charger.
Starter Battery
24V+
Service Battery
24V+
Service ground
Service Battery Midpoint
D250TS
The D250TS has one 24V input and two alternating outputs. One output charge a 24V
battery and the other provides 50% of the input voltage to the midpoint of a 24V system. This
enables connection of 12V consumers to the battery string and also equalizing this battery
string, for longer battery life.
D250TS
FEATURES:
Multi-step10A temperature compensated battery charging and battery maintenance.
Battery separation of Starter and Service batteries.
Equalization of Service batteries
Makes connection of 12V consumers directly to 24V Service battery possible.
When the charger is correctly connected the charger will output 24V on the status signal wire.
Connection of a 24V lamp (max 2W) to the status signal wire will indicate a correctly con-
nected charger.
The charger will maintain the starter battery untill the supply is below 14V. To avoid draining the
service battery always connect a charger to the service battery when the vehicle is not used for
a longer period.
+IN +OUT
EQU
D250TS
Status signal wire
Temperature sensor
20015884C D250TS, Manual, Print file 002.indd 3 2011-12-20 13:27:12
4 • EN
INSTALLATION OF UNIT
1. Attach the temperature sensor holder on a flat surface on one Starter battery. Position it as close
as possible to a positive post.
2. Use the included drill template. Wiring is simplified if the units are installed according to the drill
template, but other setups are possible.
3. Install the unit(s) on a flat surface where it can be properly fixed and where the unit is not
exposed to fuels, oils or splashes of dirt.
4. Mount the unit with screws intended for the surface and attach it with one screw in each of the
four holes in the corners of the unit. See picture 1. Mount the unit with M4 or ST4.2 screws. The
required torque depends on the surface for mounting.
Figure 1
2Nm
DRILL TEMPLATE
Ø 5mm
168
mm
90,6
mm
Service ground
Service Battery
24V+
Starter Battery
24V+
Status signal wire
Temp sensor
Service Battery Midpoint
20015884C D250TS, Manual, Print file 002.indd 4 2011-12-20 13:27:13
EN
EN • 5
FUNCTIONALITY
The D250TS has three operating modes:
1. 4-step charging of a Starter battery.
2. When Starter battery is fully charged: Equalization of a Service battery on the Input side. This
function provides the possibility to connect 12V consumers to the 1st battery in the Service
battery string.
3. Monitoring. The D250TS now monitors if the Starter battery needs charging (priority) or the
Service battery needs equalization.
B-1
B-2
B-3
IN
GNC
A
OUT
c2
c1
DC/DC
24V/1CA
ALTERNATOR
STARTER MOTOR
SERVICE
BATTERY
SERVICE
BATTERY
STARTER
BATTERY
STARTER
BATTERY
20015884C D250TS, Manual, Print file 002.indd 5 2011-12-20 13:27:13
6 • EN
STEP 1 DESULPHATION
Detects sulphated batteries. Pulsing current and voltage, removes sulphate from the lead plates of
the battery restoring battery capacity.
STEP 2 BULK
Charging with maximum current until approximately 80% battery capacity.
STEP 3 ABSORPTION
Charging with declining current to maximize up to 100% battery capacity.
STEP 4 PULSE
Maintaining the battery at 95–100% capacity. The charger monitors the battery voltage and
gives a pulse when necessary to keep the battery fully charged.
CHARGING PROGRAM D250TS
The D250TS will charge the Starter battery in 4 steps. The last step, Pulse maintenance means that the D250TS monitors the
Starter battery to see when a new charge pulse is needed. The D250TS use this monitoring time to equalize the Service battery by
sending out a voltage of exactly 50% of the input voltage. This prolongs the Service battery significantly and will also make it pos-
sible to connect 12V consumers to the first battery in the Service battery string. Equalization ends when the Starter battery needs
charging or when the two batteries in the Service battery bank have the same voltage.
1
DESULPHATION BULK ABSORPTION
1 2 3
PULSE
4
VOLTAGE (V)CURRENT (A)
20015884C D250TS, Manual, Print file 002.indd 6 2011-12-20 13:27:14
EN
EN • 7
TECHNICAL SPECIFICATIONS
Charger model
CTEK D250TS
Model number
1048
Input voltage
14–30V
Charging voltage
28.8V at 25°C, temperature compensated. Voltage reduced at
higher voltage, increased at lower.
Charging current
10A
Equalization current
Max 10A, average pending time used for Starter battery
charging
Equalization voltage
50% of input voltage
Back current drain
<1Ah/month
Current ripple
<4%
Ambient temperature
-20°C to +50°C, output power reduced automatically at high
temperatures
Status signal
+24V ON when D250TS is working properly. Max current
500mA.
Battery types
All types of lead-acid batteries
(WET, MF, Ca/Ca, AGM and GEL)
Battery capacity
28–200Ah
Dimensions
192 x 110 x 65 mm (L x W x H)
Insulation class
IP65
Weight
0.7kg
WIRE DIMENSIONS
Recommended minimum wire dimensions in mm²
MIN WIRE DIMENSIONS
WIRE 0.5m 1m 2m 5m 10m
+IN
2.5mm
2
2.5mm
2
4mm
2
4mm
2
4mm
2
+OUT
2.5mm
2
2.5mm
2
4mm
2
6mm
2
6mm
2
+A
2.5mm
2
2.5mm
2
4mm
2
6mm
2
6mm
2
+SIGNAL
1.5mm
2
1.5mm
2
1.5mm
2
1.5mm
2
1.5mm
2
–GROUND
1.5mm
2
1.5mm
2
1.5mm
2
1.5mm
2
1.5mm
2
20015884C D250TS, Manual, Print file 002.indd 7 2011-12-20 13:27:14
8 • EN
CTEK PRODUCTS ARE PROTECTED BY TEMPERATURE PROTECTION
D250TS has a temperature sensor that is used for adjusting the charge voltage according to
Starter Battery temperature. This sensor should be attached to the Starter Battery, if possible,
otherwise in it close surrounding.
LIMITED WARRANTY
CTEK SWEDEN AB, issues this limited warranty to the original purchaser of this product. This
limited warranty is not transferable. The warranty applies to manufacturing faults and material
defects for 2 years from the date of purchase. The customer must return the product together
with the purchase receipt. This warranty is void if the battery charger has been opened,
handled carelessly or repaired by anyone other than CTEK SWEDEN AB or its authorised
representatives. One of the screw holes in the bottom of the charger is sealed. Removing
or damaging the seal will void the warranty. CTEK SWEDEN AB makes no warranty other
than this limited warranty and is not liable for any costs other than those mentioned above.
For example, consequential damages are not covered. Moreover, CTEK SWEDEN AB is not
obligated to any other warranty other than this warranty.
SUPPORT
CTEK offers professional custom support: www.ctek.com. For the latest revised user ma-
nual, see www.ctek.com. By e-mail: info@ctek.se, by telephone: +46(0) 225 351 80,
by fax: +46(0) 225 351 95. By mail: CTEK SWEDEN AB, Rostugnsvägen 3,
SE-776 70VIKMANSHYTTAN, SWEDEN.
VIKMANSHYTTAN, SWEDEN 2011-09-01
Bengt Hagander, President
CTEK SWEDEN AB
2011-09-19
20015884C
Patents Designs Trade marks
EP10156636.2 pending RCD 509617 CTM 669987
US12/780968 pending US D575225 CTM 844303
EP1618643 US D580853 CTM 372715
US7541778 US D581356 CTM 3151800
EP1744432 US D571179 CTM 1461716 pending
EP1483817 pending RCD 321216 CTM 1025831
SE524203 RCD 000911839 CTM 405811
US7005832B2 RCD 081418 CTM 830545751 pending
EP1716626 pending RCD 001119911-0001 CTM 1475420 pending
SE526631 RCD 001119911-0002 CTM 1935061 pending
US7638974B2 RCD 081244 V28573IP00
EP1903658 pending RCD 321198 CTM 1082141 pending
EP09180286.8 pending RCD 321197 CTM 2010004118 pending
US12/646405 pending ZL 200830120184.0 CTM 4-2010-500516 pending
EP1483818 ZL 200830120183.6 CTM 410713
SE1483818 RCD 001505138-0001 CTM 2010/05152 pending
US7629774B2 RCD 000835541-0001 CTM1042686
EP09170640.8 pending RCD 000835541-0002 CTM 766840 pending
US12/564360 pending D596126
SE528232 D596125
SE525604 RCD 001705138 pending
US D29/378528 pending
RCD 201030618223.7 pending
US RE42303
US RE42230
20015884C D250TS, Manual, Print file 002.indd 8 2011-12-20 13:27:14
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ctek D250TS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ctek D250TS in de taal/talen: Engels als bijlage per email.

De handleiding is 1,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Ctek D250TS

Ctek D250TS Gebruiksaanwijzing - Nederlands - 6 pagina's

Ctek D250TS Gebruiksaanwijzing - Deutsch - 6 pagina's

Ctek D250TS Gebruiksaanwijzing - Français - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info