517218
18
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
18
Installation instructions
Before beginning with installation, be sure to observe our
recommendations and safety instructions.
Some parts are preassembled.
Step 1:
Installation of front foot (2) and rear foot (8) on the main frame (1).
1. Place the bolts (4) and each two washers (5), spring washers (6)
and nuts (7) ready for use beside the front and rear part of the main
frame (1).
2. Place the front foot (2) and rear foot (8) into the bracket of the main
frame (1) and align so that the hole patterns of the bracket and the
foots are in conformance.
(Note: The front foot caps with transport roller units (3) installed in
the front foot bar (2) must point forwards (as viewed when training,
standing on the machine).
3. Push one screw (4) each through the bores.
4. Install one washer (5) and one spring washer (6) each on the ends
of the screws (4) and fasten with one nut (7) each. (You can use
adjustable screw (67) to level the bike.)
Step 2:
Connecting the computer cables (13+14) and installation of handle-
bar post (15).
1. Place the lower end of the handlebar post (15) against the main
frame (1). Connect the two ends of the computer cable (13) and (14)
projecting from (1) and (15).
2. When the electrical cable connections have been made, push the
handlebar post (15) into the main frame (1). (Note. When pushing the
tubes together, ensure that the electrical cable connection is not
trapped. The short tube welded crosswise to the upper end of the
tubular support (15) must point forwards (as viewed when training
standing on the machine).
3. Push one spring washer (6) and one washer (5) on each of the bolts
(12). Push the bolts (12) through the bores in the main frame (1),
screw into the threaded holes of the handlebar post (15) and tighten
firmly.
Step 3:
Installation of the right (20) and left handgrip (18) on the handlebar
post (15) with the axle support (17).
1. Push the axle support (17) centrally into the tube welded crosswise
to the handlebar post (15).
2. Push on the handgrip (20) from the right hand side and the handgrip
(18) from the left hand side.
(Note. After installation, the handgrips must be aligned in such a
manner that the upper ends are inclined outwards (from handlebar
post (15)).
3. Push one spring washer (6) and one washer (16) onto each screw
(12), screw the screws (12) into the threaded holes at both ends of
the axle support (17) and tighten firmly.
(Note. The handgrips are heavier at the top than at the bottom. Twist
the handgrips downwards until further installation is conducted.)
18

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Christopeit-EL-8---9824

Zoeken resetten

  • Na jarenlang sportplezier weigert mijn crosstrainer. Bij het aansluiten van de adopter op de crosstrainer begint deze meteen te piepen. Als ik de testknop indruk gebeurt er helemaal niets meer. Weet iemand een oplossing voor dit probleem?> Gesteld op 14-5-2020 om 21:46

    Reageer op deze vraag Misbruik melden
  • Heeft u misschien een handleiding voor mij van een crosstrainer el 8 .
    Bij voorbaat hartelijk dank.
    Ron Gesteld op 8-8-2014 om 12:28

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Christopeit EL 8 - 9824 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Christopeit EL 8 - 9824 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info