815487
11
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
11
FITTING THE OPTIONAL ADD-IN BOILER
FLUE CONNECTION AND INFILLING
The boiler replaces the rear firebrick and is reversible so that
the 1’’ B.S.P. male tappings may come on either the left or the
right hand side of the boiler.
The boiler tappings protrude from the sides of the appliance
and it will therefore be necessary to fit the boiler into the
appliance after positioning the appliance in the fireplace if the
fire surround is already fitted.
Before fitting the boiler, remove the front firebars, the side
and back fire plates and the firebricks. Knock out the knock-
outs for the boiler tappings on the appropriate side of the
firebox.
Remove the backnuts and fibre washers from the boiler
tappings and fit the boiler into the appliance. Place the fibre
washers over the tappings on the outside of the appliance and
fit the backnuts, ensuring that the boiler is held tightly against
the rear inside face of the appliance and that the top edge of
the boiler is level or runs uphill to the flow tapping.
When re-fitting the firebricks, note that the short side
firebrick supplied with the boiler must be fitted on the same
side as the boiler tappings. One of the original side firebricks is
fitted on the other side, and the rear firebrick is discarded.
The firebricks must be fire cemented into position, wetting the
firebox will improve the adhesion.
Replace the back fireplate, the side fireplates, the front firebar
and the throat plate.
Connect the boiler to the heating system ensuring that the
flow pipe rises from the boiler. Fill the system with water and
check for leaks.
Make the flue connection with the special 150°elbow part no.
010/AV12. Please note that this item is ordered separately
from the appliance. The legs of the elbow may be cut on site
to suit the chimney. Also note that the legs of the elbow are
different lengths to enable some situations to be catered for by
turning the elbow around.
The end of the flue pipe must line up with the centre-line of
the chimney, and must also extend to the point where the
chimney narrows to its final size. Any large voids must be
filled and flaunched to the flue pipe to ensure that all soot
deposits can be cleared when the appliance is swept, and to
prevent problems with the operation of the appliance.
Ensure that the flue pipe is not obstructed or restricted in any
way and that all joints are well sealed.
Before infilling cover the front of the appliance to protect it.
Ensure that the flue pipe is central and then fill the space
between the body of the appliance and the structural
brickwork with vermiculite (e.g. micafil or similar) concrete.
Ensure that there are no air pockets. The recommended mix
is six volumes of vermiculite granules to one volume of
Portland cement thoroughly mixed together. Enough water
should be added so that no more than one or two drops of
water are released when a handful of the mixture is
squeezed.
After filling with vermiculite concrete flaunch the top of the
flue connector pipe to the chimney with lime mortar. Ensure
that the flue pipe is well sealed to the chimney.
Make good the hole(s) in the chimney breast making sure that
it is completely airtight. A typical installation is shown in Fig. 7.
®
INSTALLATION INSTRUCTIONS
150°
0
4
5
1
2
3
Fig. 7. Typical Installation
Vermiculite
Infill
Flaunching
Take Flue Pipe
Up To Narrowest
Part Of Chimney.
Part No. 010/AV12
150° Elbow
charnwood
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Charnwood LA20i bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Charnwood LA20i in de taal/talen: Engels als bijlage per email.

De handleiding is 0.43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info