815487
10
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
10
PREPARATION OF FIREPLACE
FITTING THE FIRE
Before fitting the appliance into an existing fireplace remove
the fireback and any loose in-fill material.
The hearth, surround and opening for the appliance must
conform with Figs. 4 and 5. The flat area around the opening
must be a minimum of 750 mm wide and 660 mm high.
Ensure that the hearth and the base in the opening are flat,
level, and at right angles to the surround.
Make a hole in the front of the chimney breast to give access
for infilling and fixing the flue pipe. If the optional boiler is to
be fitted it will also be necessary to make a hole in the side of
the chimney breast to give access for the pipework.
In some cases it may be necessary to place the connecting flue
pipe in the chimney before fitting the fire into the fireplace.
Apply fire cement to the rear face of the sealing flange on the
appliance. Fit the appliance into the opening ensuring that it is
central and that a good seal is made between the sealing
flange and the face of the surround.
Remove any excess fire cement from around the sealing
flange.
The appliance should be screwed to the hearth through the
holes at the base of the sealing flange.
The optional add-in boiler which may be fitted in the
appliance has an output sufficient for domestic hot water
heating. If the boiler is fitted then the room heating will be
reduced.
The hot water system should be a gravity circuit and must be
correctly vented as shown in Fig. 6.
The steel boiler in conjunction with a double feed indirect hot
water storage cylinder to BS:1566 part 1 should be used in
most situations, unless the appliance is to be fitted in a soft
water area in which case the stainless steel boiler may be used
with a direct hot water cylinder.
All pipework in the primary circuit must be 28mm diameter
and the flow pipe must rise continuously from the boiler to
the open vent.
If an indirect cylinder is used then the primary circuit should
be filled with a suitable inhibitor to prevent the build up of
scale and corrosion.
HOT WATER SYSTEM
®
INSTALLATION INSTRUCTIONS
A
B
405 mm
400 mm
Minimum
This Dimension Is The
Minimum Level Area
Required To Enable The
For Overall Sizes Of
Hearth See The
Section Titled "Hearth".
Doors To Be Opened.
Fig. 4. Limiting Dimensions Of Hearth
660 mm
The shaded area on the face of
the surround is the minimum flat
area required.
750 mm
Fig. 5. Limiting Dimensions Of Surround And Opening
Drain Cock at Lowest Point
Drain Cock
Indirect Hot Water Cylinder
Cold Water Tank
Overflow
Feed and Expansion Tank 22mm Open Vents
Overflow
Domestic Hot Water Draw Off
Gravity Return 28mm
Gravity Flow 28mm
Fig. 6. Typical Gravity Hot Water System
charnwood
Dimension A:
Max. 470mm (18 ”)
Min. 405mm (16")
Dimension B:
Max. 575mm (23")
Min. 555mm (21 ”)
½
¾
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Charnwood LA20i bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Charnwood LA20i in de taal/talen: Engels als bijlage per email.

De handleiding is 0.43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info