Warning / Caution
Pay careful attention to your surroundings when using the •
computer.
Install the magnet, sensor, and bracket securely. Check these •
periodically.
If a child swallows a battery, consult a doctor immediately.•
Do not leave the computer in direct sunlight for a long period •
of time.
Do not disassemble the computer.•
Do not drop the computer to avoid malfunction or damage.•
Do not carry computer in back pocket of pants. Sitting down with •
the computer put in back pocket of pants may damage the unit.
When using the computer installed on the bracket, change the •
MODE by pressing on the three dots below the screen. Pressing
hard on other areas can result in malfunction or damage to the
computer.
Be sure to tighten the dial of the FlexTight™ bracket by hand. •
Tightening it strongly using a tool, etc. may damage the screw
thread.
Dispose of used batteries according to local regulations.•
LCD screen may be distorted when viewed through polarized •
sunglass lenses.
Walk mode
The unit may not make measurement correctly in the following
environments and actions.
When the unit moves irregularly in a bag•
When walking irregularly in sandals or wooden clogs•
When walking or jogging as if shuffl ing•
When walking is disturbed on a crowded road•
When standing up or sitting down•
When walking up and down a stairway or steep slope•
When getting on a vehicle (car, train, etc.)•
Wireless sensor
The sensor was designed to receive signals within a maximum
range of 70 cm, to reduce chance of interference. When adjusting
the wireless sensor, note the following:
Signals cannot be received if the distance between the sensor •
and the computer is too large.
The receiving distance may be shortened due to low tempera-•
ture and exhausted batteries.
Signals can be received only when the back of the computer •
is facing the sensor.
Interference may occur, resulting in incorrect data, if the
computer is:
Near a TV, PC, radio, motor, or in a car or train.•
Close to a railroad crossing, railway tracks, TV stations and/•
or radar base.
Using with other wireless devices or some particular battery •
lights in close proximity.
Replacing the battery
Computer
If
turns on, replace the battery.
CAUTION:
Reset measured data manually just before replacing the •
battery. Today’s measurement data is not saved when you
go through the restart operation without resetting data.
(
How to use : Resetting data)
Do not combine old and new batteries or different types of bat-•
teries. Do not insert them in the reverse direction.
Remove the battery case cover, and hold the battery holder
1.
tab to pull out the battery. The battery holder is lifted when
either tab is pulled up.
2.
Insert 2 new lithium batteries (CR2032) in the battery holder, with
the (+) side facing each other.
3. Press the AC button (restart operation)
The whole screen illumination is turned
on.
In the restart operation, the record data *
of the speed unit, date, tire circumfer-
ence, weight, stride, and data view are
maintained.
Set the date4.
For procedures, refer to
“Preparing the computer 4”.
When setting the date, the latest record date in the data view is initially displayed, *
and any date before that cannot be set.
Set the clock5.
For procedures, refer to “Preparing the computer 5”.
The time when the restart operation was performed is initially *
displayed on the screen.
In the restart operation, the speed unit, date, tire circumference, weight, *
stride, and data view are maintained.
Speed sensor
When the sensor signal is hardly received
in the bike mode, replace the battery.
Install a new lithium battery (CR2032)
with the (+) side facing upward.
After replacement, review the instal-*
lation conditions, and check the po-
sitions of the sensor and magnet.
(
How to install the unit on your
bicycle)
Trouble shooting
Check the following items before contacting us.
MODE does not change when the computer is mounted on its bracket.
Check that there is no dirt between the bracket and the computer.
Wash off the bracket with water to get rid of any dirt.
The current speed is not displayed
Check that the clearance between the speed sensor and magnet is not too
large. (Clearance: within 5 mm)
Check that the magnet passes through the sensor zone correctly.
Adjust the positions of the magnet and speed sensor.
Is the computer installed at the correct angle?
Back of computer must face toward the speed sensor.
Check that the distance between the computer and speed sensor is correct.
(Distance: within 70 cm)
Install the speed sensor within the specifi ed range.
Is the computer or sensor battery weak? In winter, battery performance
diminishes.
Replace with new batteries. (
Replacing the battery)
No display even after pressing the button
Is battery in the computer run down?
Replace with new batteries. (
Replacing the battery)
Incorrect data appear.
Replacing the battery, Steps 3 to 5 (Restarting operation)
Maintenance
To clean the computer or accessories, use diluted neutral
detergent on a soft cloth, and wipe it off with a dry cloth.
Specifi cation
Battery Computer: Lithium battery (CR2032) x 2
Sensor: Lithium battery (CR2032) x 1
Battery life Computer:
Bike mode About 1 year if it is used for 1
hour per day
Walk
mode
Walk mode: About 4.5 months when
using it for 10000 steps a day
Sensor: About 10000 km
This is the average figure of being used under 20 °C *
temperature and the distance between the computer and
the sensor is 65 cm.
Controller 8 bit, 1-chip microcomputer
(Crystal controlled oscillator)
Display Liquid crystal display
Sensor
No contact magnetic sensor, Acceleration
sensor
Transmission
distance
Within 70 cm
Tire circum-
ference range
0100 mm - 3999 mm
(Initial value: 2096 mm)
Working
temperature
32 °F - 104 °F (0 °C - 40 °C) (This product will
not display appropriately when exceeding the
Working Temperature range. Slow response
or black LCD at lower or higher temperature
may happen respectively.)
Dimensions/
weight
Computer: 1-13/16” x 1-59/64” x 1/32” (46 x
49 x19.5 mm) / 1.3 oz (37 g)
Sensor:
1-41/64” x 1-27/64” x 19/32” (41.5
x 36 x 15 mm) / 0.5 oz (15 g)
The factory-loaded battery life might be shorter than the *
above-mentioned specifi cation.
The specifi cations and design are subject to change without *
notice.
Limited warranty
2-Year Computer only
(Accessories and Battery Consumption excluded)
CatEye cycle computers are warranted to be free of defects from
materials and workmanship for a period of two years from original
purchase. If the product fails to work during normal use, CatEye
will repair or replace the defect at no charge. Service must be
performed by CatEye or an authorized retailer. To return the
product, pack it carefully and enclose the warranty certifi cate
(proof of purchase) with instruction for repair. Please write or
type your name and address clearly on the warranty certifi cate.
Insurance, handling and transportation charges to CatEye shall
be borne by person desiring service.
For UK and REPUBLIC OF IRELAND consumers, please return
to the place of purchase. This does not affect your statutory
rights.
