Handleiding Casio QW3475 - GBD-H1000 G-SQUAD (pagina 24 van 58) (Engels)

740165

Verklein

Vergroot

Pagina terug

1/58

Pagina verder

Note

●

Pressing (C) (step 3 of this procedure)

before the [GPS CAPTURE] message

appears causes run timing to start

using the watch’s accelerometer. Note

that your route is not recorded during

run timing using the accelerometer.

If you want your route to be recorded,

make sure that the [GPS CAPTURE]

message is displayed before you start

run timing.

●

It can take from about 30 seconds to

two minutes after you press (C) in step

2 for run timing using GPS to become

enabled. Under some signal reception

conditions, it may take as long as five

minutes.

Enabling run timing using GPS will

automatically cause the Training Mode

screen to appear.

Training Mode

3. Press (C).

Start run timing.

Note

●

The screen shown in step 2 of the

above procedure will not appear if the

Airplane Mode is enabled or if the GPS

setting is off.

●

You can find out the current GPS status

by checking whether or not the

mark on the display is flashing.

Not flashing: GPS enabled

Flashing: GPS disabled (Watch is

searching for GPS signals.)

●

After [GPS CAPTURE] appears and

is on the display, it means that the

GPS signal was lost and the watch is

searching for a signal.

●

If, while run time is being performed,

starts flashing on the display or

appears on the display, it means that

the watch is performing measurement

using its accelerometer and that your

route is not being recorded.

●

Entering the settings of the Compass,

Altimeter, Barometer, or Temperature

Mode during training will cause run

timing using GPS to stop momentarily.

The watch will start searching for GPS

signals again when you exit the setting.

If you want to use GPS for your run

timing, wait until [GPS CAPTURE]

appears on the display before you

start.

●

Pausing Run Timing

1. While the run timing screen is displayed,

press (C).

This pauses run timing and displays the

pause menu screen.

Pause Pause menu

2. Use (A) and (D) to select what you want to

do with the run timing data you have just

measured.

[RESUME] Resumes timing.

[SAVE] Saves data.

[DELETE] Deletes data.

3. Press (C).

●

If you select the data save option, the

run timing result screen will appear.

Pressing any button returns to the

Timekeeping Mode.

●

If you select the data delete option, the

watch returns to the Timekeeping

Mode.

●

Measuring Lap Times

Start run timing.

Starting Run Timing

2. Press (E).

Each press of (E) displays the elapsed

time of the current section or lap (lap time)

to appear.

Split time, lap distance

Lap time

Heart rate (average, maximum)

3. Press (A) or (D) to return to the run timing

screen.

●

If you do not perform any button

operation, the watch will return to the

run timing screen automatically after

about 10 seconds.

Note

●

You can change the lap time display

using G-SHOCK MOVE. Each of the

screens displays the items below.

ー　

Heart rate [AVG] (average), lap time,

[SPLIT TIME] (split time)

ー　

Heart rate [MAX] (maximum), lap

time, [DISTANCE] (lap distance)

Changing Display

Information During Run

Timing

One of three screens can be displayed during

run timing (Training Mode), and you can

specify the items you want to appear on each

screen.

This means you can configure a screen with

the items you want to monitor and display that

screen while you train.

Specifying the Screen to be Displayed

During Running (RUN FACE)

You can navigate between display screens by

pressing (A).

Example:

Changing the GPS Receive

Interval

Use the procedure below to specify the

interval for receiving GPS signals to acquire

location information while running.

1. Enter the Timekeeping Mode.

Navigating Between Modes

2. Press (C).

This displays the GPS signal receive start

screen.

3. Press (A) or (D).

This displays the Training Mode screen.

4. Hold down (A) for at least two seconds.

This displays the Training Mode setting

screen.

Pointer

Operation Guide 3475

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Casio QW3475 - GBD-H1000 G-SQUAD Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info