506039
29
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
E-28
If you do not want to receive and append any more data
items, skip steps 4 and 5.
5. Repeat step 3 to receive more data.
The ! indicator means that data items will be printed
one at a time. If you want to print all of the received data
items at once, press B to change ! to A. Press B
again to change back to !.
6. Press PRINT to print the data.
If ! is on the display, pressing PRINT prints the single
data item where the cursor is currently located. Use u
and i to move the cursor to the data item you want to
print.
If A is on the display, pressing PRINT prints all of the
received data items.
Use a tape that is at least 9mm wide when printing re-
ceived data items.
You can enlarge received data item character size verti-
cally by a factor of two and horizontally up to a factor of 4.
Use a tape width of at least 18mm when received data
item character size is increased vertically by a factor of
two.
None of the following functions can be used with received
data: frames, preset formats, auto sizing, preset layouts,
block operations, proportional character spacing, smooth-
ing, character input settings, character deletion, text stor-
age into memory, text recall from memory.
The printer returns to the screen in step 3 (the one that
appears after data communication is complete) after print-
ing is complete.
7. Press ESC SET to quit data communications.
All received data is cleared from label printer memory when
you quit data communications.
8. Turn the label printer and Copy Pen off and disconnect
the cable.
Importing Data from a Graphic Scientific
Calculator
Use the following procedure to send data to the label printer
from one of the following CASIO Graphic Scientific Calcula-
tor models: CFX-9800G, RM-9800G, fx-7700GH, fx-
9700GH, CFX-9850G, CFX-9950G.
Important!
Note that some of the steps you need to perform in the
following procedure depend on the graphic scientific cal-
culator model you are sending data from.
Before performing any of the procedures in this section,
make sure that the width of the tape loaded in your label
printer is 9mm or greater.
To connect the graphic scientific calculator to
the label printer
1. Turn off the power of the label printer and the calculator.
2. Use the optionally available SB-62 Connecting Cable to
connect the calculator to the label printer.
You have to remove the connector cover of the graphic
scientific calculator to attach the cable. Keep the connec-
tor cover in a safe place so you can replace it later.
3. Turn on the calculator and then the label printer.
To send data from a graphic scientific
calculator to the label printer
1. Set up the calculator to send data.
CFX-9850G, CFX-9950G
In the data communication main menu, press F6 (IMGE),
and then select Monochrome for Image Set.
F2 (MONO)
Next, display the screen you want to send.
fx-7700GH, fx-9700GH
Display the setup screen and specify COPY as the func-
tion of the M-Disp key.
Next, display the screen you want to send.
CFX-9800G, RM-9800G
Display the setup screen and press F3 (MON) to specify
MONOCHR as the function of the M-Disp key.
Next, display the screen you want to send.
2. On the label printer, press FUNC, DEL (COMM) and then
SET to set it up to receive data.
The above operation causes the message RECEIVE OK!
to appear on the label printers screen to indicate that it is
standing by to receive data. If you do not perform the next
step within 20 seconds after this message appears, the
message changes to SEND ERROR! If this happens,
press ESC and start again.
3. Start the data send operation on the calculator.
CFX-9850G, CFX-9950G
Press [F<>D].
fx-7700GH, fx-9700GH, CFX-9800G, RM-9800G
Press M-Disp.
4. After data communication is complete, the screen of the
label printer appears as shown below.
1ATAD
1
MM
O
C
m
c9.41×1
The received data is indicated on the display as DATA 1,
DATA 2, and so on. Up to 15 data items can be received,
as long as the total length of the tape to print the data
items does not exceed 250mm.
If the message SEND ERROR! is on the screen, press
ESC and try again.
5. On the label printer, press CAPS to specify the receive
mode of additional data items.
Each press of CAPS toggles label printer between the
following two modes.
COMM
Received data is appended to the end of previously
received data.
COMM
Received data replaces previously received data.
If you do not want to receive and append any more data
items, skip steps 5 and 6.
6. Press SET and repeat step 3 to receive more data.
The ! indicator means that data items will be printed
one at a time. If you want to print all of the received data
items at once, press B to change ! to A. Press B
again to change back to !.
7. Press PRINT to print the data.
If ! is on the display, pressing PRINT prints the single
data item where the cursor is currently located. Use u
and i to move the cursor to the data item you want to
print.
If A is on the display, pressing PRINT prints all of the
received data items.
Use a tape that is at least 9mm wide when printing re-
ceived data items.
You can enlarge received data item character size verti-
cally by a factor of two and horizontally up to a factor of 4.
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio KL8200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio KL8200 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio KL8200

Casio KL8200 Gebruiksaanwijzing - Deutsch - 39 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info