Handleiding Casio 5347 - OCW-S3001 (pagina 6 van 7) (Engels)

624834

Verklein

Vergroot

Pagina terug

1/7

Pagina verder

Operation Guide 5347 (OC)

E-40

Hand/Day Adjustment Steps

For full details, see the procedure from page E-41 to E-43.

Pull crown out to second click.

Second Hand

Minute Hand

Hour Hand

Upper Dial Big Hand

Upper Dial Small Hand

Mode Hand

Day Indicator

(Wait for at least six seconds until the

Second Hand moves to 12 o’clock.)

Lower Dial Big Hand

Lower Dial Small Hand

Mode Hand*

Day Indicator*

Auto Adjustment

Manual Adjustment

* Perform this operation only if you are unable to align the

Mode Hand and

Day Indicator using the

operation to the right.

x After completing adjustment, push the crown back in. Pushing the crown back in part way through

adjustment will return to the mode you started from, with any adjustments you made in effect.

E-41

To adjust the hand and day home positions

Important!

x You do not need to perform the procedure in this section if the watch is indicating the time and/or day

correctly.

1. Pull the crown out to the second click.

2. Keep B depressed for more than six seconds. This will cause the

Second Hand moves to

12 o’clock.

x After about one second, the

Second Hand moves to A (a.m.) or P (p.m.). After about six seconds,

the

Second Hand moves to 12 o’clock.

x Release B after the

Second Hand moves to 12 o’clock. At this time the watch will start automatic

adjustment of the

Second Hand,

Minute Hand, and

Hour Hand positions.

x Adjustment is complete when the

Second Hand,

Minute Hand, and

Hour Hand move to

12 o’clock.

3. Press B.

x The

Second Hand,

Minute Hand, and

Hour Hand will

move to 2 o’clock.

x The

Upper Dial Big Hand and

Upper Dial Small Hand will

move to 12 o’clock and stop there.

x If the

Upper Dial Big Hand and

Upper Dial Small Hand

do not align with 12 o’clock, rotate the crown to adjust them

so they do.

x You can use high-speed hand movement to perform this step.



 



E-42

4. Press B.

x The

Lower Dial Big Hand and

Lower Dial Small Hand will

move to 12 o’clock and stop there.

x If the

Lower Dial Big Hand and

Lower Dial Small Hand

do not align with 12 o’clock, rotate the crown to adjust them

so they do.

x You can use high-speed hand movement to perform this step.

5. Press B.

x Check if the

Mode Hand is stopped at 12 o’clock and the

Day Indicator indicates the day correctly.

x If the position of the

Mode Hand and/or

Day Indicator

is not correct, rotate the crown to adjust the

Mode Hand to

12 o’clock and the

Day Indicator so the day is in the center

of indicator window.

x You can use high-speed hand movement to perform this step.

x When you rotate the crown, there is a limit on the movement of

the

Mode Hand and

Day Indicator. The maximum range

of movement of the

Mode Hand is 180 degrees left and right.

The

Day Indicator can move just a little (page E-2).

x If you successfully align the

Mode Hand and

Day

Indicator, advance to step 7. If you are unable to align the

Mode Hand and

Day Indicator, go to step 6.



 



 

Day Indicator during home position

adjustment

E-43

6. Press B.

x Wait until the

Mode Hand stops at 12 o’clock and the

Day

Indicator stops at 1.

x The

Mode Hand may continue to rotate for as long as

30 minutes until the

Day Indicator stops at 1 (page E-2).

x If the

Mode Hand and/or

Day Indicator is not aligned

properly when they stop moving, rotate the crown to adjust

them so the

Mode Hand is at 12 o’clock and so 1 is in the

center of the

Day Indicator window.

x You can use high-speed hand and day movement to perform

this step.

7. Push the crown back in.

This exits the adjustment mode and returns to normal timekeeping.

Important!

x Leaving the crown pulled out for more than approximately 30 minutes without performing any operation

will automatically cause the adjustment operation to become disabled. If this happens, push the crown

back in and then pull it out to restart the above procedure from the beginning.

Pushing the crown in will return to the mode you started from in step 1 with the hands and/or day in

their newly adjusted positions.



 

E-44

Troubleshooting

Hand Movement and Position

■ I lost track of what mode the watch is in.

Refer to “Mode Reference Guide” (page E-22). To return directly to the Timekeeping Mode, pull out the crown

to the ﬁ rst click hold down B for at least two seconds. To return to the Timekeeping Mode, push the

crown back in.

■ The

Second Hand is moving at two-second intervals.

Power may be low. Expose the watch to light until the

Second Hand starts moving normally, at one-

second intervals (page E-10).

■ The hands of the watch suddenly start moving at high speed, even when I do not perform any

operation.

This could be due to any one of the following causes. In all cases, the hand movement does not indicate

malfunction, and should stop shortly.

x The watch is recovering from a sleep state (page E-12).

x The time setting is being adjusted following a successful auto time calibration signal receive operation

(page E-13).

■ Hands suddenly stop moving. Button operation also is disabled.

The watch may be in the power recovery mode (page E-11). Do not perform any operation until the hands

return to their normal positions (in about 15 minutes). The hands should return to their correct positions when

normal operation returns. To help power recover, leave the watch in a location where it is exposed to light.

■ All hands are at 12 o’clock and nothing happens when I press any button.

The rechargeable battery is dead. Expose the watch to light to charge the battery and restore normal

operation.

E-45

■ The current time setting is off by hours.

x Your city setting may be wrong. Check your city setting and correct it, if necessary (page E-28).

■ The current time setting is off by one hour.

x If you are using the watch in an area where time calibration signal reception is possible, see “To select

a city” (page E-28).

x The period when summer time is applied in the location where you are using the watch may be

different from the period set for your currently selected city. Use the procedure under “To switch

between standard time and summer time manually” (page E-31) to switch from AT (AUTO) to STD (for

standard time) or DST (for summer time).

■ The hands and/or day indications are off.

This could indicate that the watch has been exposed to magnetism or strong impact, which has caused

problems with proper hand and day alignment. Adjust the watch’s hand and day home position alignment

(page E-39).

■ Data indication is correct, but it is not in the middle of the day indicator.

The date is in the process of changing. For information about how the date changes, see page E-2.

Charging

■ The watch does not resume operation after I expose it to light.

It can take quite a long time to charge the battery after the power level drops to Level 3 (page E-10). Continue

exposing the watch to light until the

Second Hand starts moving normally (at one-second intervals).

E-46

Time Calibration Signal

The information in this section applies only when LONDON (LON), PARIS (PAR), ATHENS (ATH),

HONOLULU (HNL), ANCHORAGE (ANC), LOS ANGELES (LAX), DENVER (DEN), CHICAGO (CHI),

NEW YORK (NYC), HONG KONG (HKG), or TOKYO (TYO) is selected as the city. You need to adjust

the current time manually when any other city is selected.

■ The

Second Hand indicates N (NO) when I check the result of the latest receive operation.

Possible Cause Remedy Page

x You are wearing or moving the watch, or

performing a button operation during the signal

receive operation.

x The watch is in an area with poor reception

conditions.

Keep the watch in an area where reception

conditions are good while the signal receive

operation is being performed.

E-16

You are in an area where signal reception is not

possible for some reason.

See “Approximate Reception Ranges”. E-14

The calibration signal is not being transmitted for

some reason.

x Check the website of the organization that

maintains the time calibration signal in your area

for information about its down times.

x Try again later.

—

■ The current time setting changes after I set it manually.

You may have the watch conﬁ gured for Auto Receive of the time calibration signal (page E-17), which will

cause the time to be adjusted automatically according to your currently selected city. If this results in the

wrong time setting, check your city setting and correct it, if necessary (page E-28).

E-47

■ Auto Receive is not performed or I cannot perform Manual Receive.

Possible Cause Remedy Page

Your city setting is wrong. Check your city setting and correct it, if necessary.

E-13

E-28

Auto Receive is disabled because there is an

ongoing elapsed time operation.

Stop the ongoing stopwatch operation. E-36

The watch is in the Stopwatch Mode.

Change to the Timekeeping Mode. If you want to

perform signal reception in the World Time Mode,

enter the World Time Mode.

E-24

The Auto Receive function is turned off. Turn on Auto Receive. E-20

The crown is pulled out. Push the crown back in. E-3

There is not enough power for signal reception. Expose the watch to light to charge it. E-9

■ Signal reception is being performed successfully, but the time and/or day is wrong.

Possible Cause Remedy Page

Your city setting is wrong. Check your city setting and correct it, if necessary.

E-13

E-28

The watch may have been exposed to magnetism

or strong impact, which has caused problems with

proper hand and day alignment.

Adjust the watch’s hand and day home positions. E-39

Casio 5347 - OCW-S3001 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info