611481
3
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
Operation Guide 5117
3
World Time
World Time shows the current time in 48 cities (29 time
zones) around the world. A simple operation swaps your
Home City with the currently selected World Time city.
The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “City Code Table” for information about
the UTC offset settings that are supported.
All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C.
City code
Current time in
selected city
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zone).
Holding down the button scrolls at high speed.
When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping.
Press A.
One second
DateHour : Minutes Seconds
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about three seconds to toggle
between Daylight Saving Time (DST indicator
displayed) and Standard Time (DST indicator not
displayed).
The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
DST indicator
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time city. This
changes your Home City to your World Time city, and your World Time city to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
If your current World Time city supports receipt of a time calibration signal, making it
your Home City enables calibration signal reception.
For information about which cities support time calibration signal reception, see “To
specify your Home City.
To swap your Home City and World Time city
1. In the World Time Mode, use D to select the World Time city you want.
2. Hold down A and B until the watch beeps.
This will make the World Time city (which you selected in step 1), your Home City. At
the same time, it changes the Home City you had selected prior to step 2 your World
Time city.
After swapping the Home City and World Time city, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time city.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
The digital display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The stopwatch hand will perform one high-speed
rotation during the first second of an elapsed time
measurement operation. Then it will indicate the
seconds during the first minute of the operation. After
that, it will indicate minutes. Whenever an elapsed time
operation is stopped, the stopwatch hand will move to
the current seconds count.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
1/100 second
Hours
Minutes
Seconds
Stopwatch hand
SPL
indicator
Exiting the Stopwatch Mode while a split time is frozen on the display clears the split
time and returns to elapsed time measurement.
All of the operations in this section are performed in the Stopwatch Mode, which you
enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Clear
D
Start
Stop Re-start Stop
D
D
D
A
Split Time
D
Start Split
(SPL indicator
displayed)
Split release Stop
A
D
A
Clear
A
D
Start
Split
First runner
finishes.
Display time of
first runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
D
A
A
Clear
A
Two Finishes
Countdown Timer
You can set the countdown timer within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero.
You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Seconds
Minutes
Start time (minutes)
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds to signal when the countdown
reaches zero. The countdown is repeated up to eight times, and then stop.
The number of the current repeat (1 to 8) is shown in the lower display.
The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about three
seconds until the minute setting of the countdown start
time starts to flash, which indicates the setting screen.
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
C
3. Perform the following operations, depending on which setting is currently selected
on the display.
While the start time setting is flashing, use D (+) and B (–) to change it.
While the auto-repeat on/off setting (
or ) is flashing on the display, press
D to toggle auto-repeat on (
) and off ( ).
l
l
l
l
l
l
l
l
l
l
l
Start time (minutes)
4. Press A to exit the setting screen.
The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
Frequent use of auto-repeat and the alarm can run down battery power.
Alarms
When an alarm is turned on, the alarm tone sounds when
the alarm time is reached. One of the alarms is a snooze
alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
There are five alarm screens numbered
, ,
and for the daily alarm, a snooze alarm
screen indicated by
. The Hourly Time Signal
screen is indicated by
.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm number
Alarm time
(Hour : Minutes)
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
To set a daily alarm, display an alarm screen ,
, and . To set the snooze alarm,
display the
screen.
is the hourly time signal setting.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A for about three seconds until the hour
setting of the alarm time starts to flash, which indicates the setting screen.
This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
To stop the alarm tone after it starts to sound, press any button.
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
setting screen
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 5117 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 5117 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio 5117

Casio 5117 Gebruiksaanwijzing - Nederlands - 6 pagina's

Casio 5117 Gebruiksaanwijzing - Deutsch - 7 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info