683279
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Recommended Power Cables [Reference]
Cable (AWG) 24 22 20 18 16
12 V DC maximum cable length m (ft.) 5 (16.4) 9 (29.5) 14 (45.9) 23 (75.5) 32 (105.0)
24 V AC maximum cable length m (ft.) 11 (36.1) 18 (59.1) 29 (95.1) 46 (150.9) 64 (210.0)
Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring.
AC Adapter
Please use the dedicated AC adapter (sold separately).
Remove the power connector attached to the AC adapter, then connect the power interface
cable included in the package, to the power connector, as shown in the following diagram.
AC Adapter
Power Interface
Cable
Black
Brown
Blue
Green
White
Insulate
External Device I/O Terminals
External device I/O terminals consist of two input and output systems each. The Viewer can
be used to check external device input status and control output to an external device (please
refer to the “Operation Guide”).
Use the included I/O interface cable to connect to external device input/output terminals.
1: BROWN External device input 1 IN1 (+)
2: BLACK External device input 1 IN1 (-)
3: RED External device input 2 IN2 (+)
4: BLACK External device input 2 IN2 (-)
5: ORANGE External device output 1 OUT1
6: YELLOW External device output 1 OUT1
7: GREEN External device output 2 OUT2
8: BLUE External device output 2 OUT2
1
8
External Device Input Terminals (IN1, IN2)
External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative
terminals connected to the camera interior GND. Connecting cables to the positive and
negative terminals and opening or closing the circuit notifies the Viewer.
Important
When connecting sensors and switches, connect terminals that are electrically isolated from the
respective power and GND.
External Device Output Terminals (OUT1, OUT2)
External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets
have no polarity. Controls from the Viewer can be used to open and close the circuit between
the terminals. Using optical couplers, the output terminals are isolated from the camera’s
internal circuit.
Internal Connection Diagram
Internal controller
External device
Input terminal
IN1, IN2
Output terminal
OUT1, OUT2
+3.3 V
0.1 µF
10 kΩ 10 kΩ
1 kΩ
External device
 
The load connected to the output terminals
should be within the following rating range.
Rating between output terminals:
Maximum voltage 50 V DC
Continuous load current at or below 100 mA
On resistance: Max. 30 Ω
Audio Input/Output Terminals
Each audio input/output terminal has one input system and one output system.
Connecting the camera to an audio input/output device such as a microphone or a speaker
with an amplifier allows you to send/receive audio through the Viewer.
Use the
3.5 mm ( 0.14 in.) monaural mini-jack connector to connect an audio input/output
device.
Audio Input Terminal Common LINE IN/MIC IN (monaural input)
Although the camera has a single audio input system, it supports two types of microphone
input: LINE IN and MIC IN. Before using the audio input, please confirm the [Audio Input] in the
Setting Page (please refer to the “Operation Guide”). LINE IN is selected by default.
Input terminal:
3.5 mm ( 0.14 in.) mini jack (monaural)
Dynamic MIC IN
Input impedance: 1.5 kΩ ±5%
* Supported microphones: Output impedance: 400 – 600 Ω
Condenser MIC IN
Input impedance (microphone bias resistance): 2.2 kΩ ±5%
Microphone power supply: plug-in power (voltage: 2.3 V)
* Supported microphones: Condenser microphones with plug-in power support
LINE IN
Input level: Max. 1 Vp-p
* Use a microphone with an amplifier.
Audio Output Terminal LINE OUT (monaural output)
Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from the
Viewer.
Output terminal:
3.5 mm ( 0.14 in.) mini jack (monaural)
Output level: Max. 1 Vp-p
* Use a speaker with an amplifier.
© CANON INC. 2017 Printed in Japan
Specifications
Please refer to the Appendix – Specifications for specifications not listed below.
Lens 2.4x optical zoom (4x digital zoom) lens (electric drive)
Viewing Angle For 16:9 aspect ratios
Horizontal: 113.4° (W) – 46.5° (T)
Vertical: 61.4° (W) – 26.2° (T)
For 4:3 aspect ratios
Horizontal: 113.4° (W) – 46.5° (T)
Vertical: 83.0° (W) – 34.9° (T)
Pan Angle Range 344° (±172°)
Tilt Angle Range 93° (-3° – +90°) Camera is at 0° when attached to the ceiling and facing straight down,
and 90° when at a horizontal position.
Rotation Angle Range 344° (±172°)
Network Terminal* LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))
* Use a category 5 or better LAN cable, 100 m (328 ft.) or less in length.
Audio Input Terminal
3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(Common LINE IN & MIC IN)
Audio Output Terminal
3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(LINE OUT)
External Device I/O Terminal
Input x 2, Output x 2
Memory Card SD Memory Card, SDHC Memory Card, SDXC Memory Card Compatible.
Operating Environment
Temperature:
Operating Temperature Range (including direct sun exposure)
AC, PoE+: -50°C – +55°C (-58°F – +131°F)
DC, PoE: -10°C – +55°C (+14°F – +131°F)
Start-up Temperature Range (including direct sun exposure)
AC, PoE+: -30°C – +55°C (-22°F – +131°F)
DC, PoE: -10°C – +55°C (+14°F – +131°F)
Humidity: 5% – 85% (without condensation)
Temperature:
Operating Temperature Range (including direct sun exposure)
PoE: -10°C – +55°C (+14°F – +131°F)
Humidity: 5% – 85% (without condensation)
Storage Environment Temperature: -30°C – +60°C (-22°F – +140°F)
Humidity: 5% – 90% (without condensation)
Installation Method Ceiling mount/Surface mount
Power Supply
PoE: PoE power supply via LAN connector
(IEEE802.3at Type1/Type2 compliant)
AC Adapter: PA-V18 (100 – 240 V AC) (sold separately)
External power source: 24 V AC/12 V DC
PoE: PoE power supply via LAN connector
(IEEE802.3at Type1 compliant)
IR Illumination Range
(T)
30 m (98.4 ft.) (When using 24 V AC, PoE+)
20 m (65.6 ft.) (When using 12 V DC, PoE)
Power Consumption
PoE+: Max. approx. 21.2 W*
1
PoE: Max. approx. 10.1 W*
2
AC Adapter PA-V18: Max. approx. 12.8 W (100 V AC)
Max. approx. 12.8 W (240 V AC)
DC: Max. approx. 11.1 W
AC: Max. approx. 22.2 W
*
1
Class 4 power sourcing equipment (requests 30.0 W)
*
2
Class 0 power sourcing equipment (requests 15.4 W)
PoE: Max. approx. 7.4 W*
* Class 0 power sourcing equipment (requests 15.4 W)
Weight
Approx. 2120 g (4.68 lb.)
Approx. 2040 g (4.50 lb.)
Dust-resistant/
Waterproof Specification IP66
Hydrophilic Coating
Available
Connecting the Camera
To prevent cable connections from shorting out, wrap each individual connection with
insulating tape, and then wrap all of the cables with waterproofing tape.
Power Connection
Power can be supplied to the camera in the three ways described below. Please be sure to
read the user manual for the dedicated power supply before use.
Note
Power supply should conform to all local codes.
The power supply should also comply with IEC/UL60950-1 (SELV/LPS) standards.
PoE+ /PoE (Power over Ethernet)
Power can be supplied to the camera by using a LAN cable connected to a PoE+/PoE HUB
that conforms to the IEEE802.3at Type2 (PoE+)/Type1 (PoE) standard.
Important
Check with your dealer for more information about PoE+/PoE HUB and Midspan technology.
Midspan (a LAN cable power supply device) is a device that, like a PoE+/PoE HUB, supplies power
to the camera via a LAN cable.
Some PoE+/PoE HUBs allow the limitation of power for each port, but applying limits may interfere
with performance. If using this type of PoE+/PoE HUB, do not limit the operating power.
Some PoE+/PoE HUBs have limits for the total power consumption for the ports, which can interfere
with performance when multiple ports are in use. For more information, check the instruction guide
for your PoE+/PoE HUB.
When the camera is connected to both a PoE+/PoE HUB and an external power
supply (12 V DC or 24 V AC), power will be supplied in the following order of precedence.
External power supply (24 V AC) > PoE+/PoE HUB > External power supply (12 V DC)
However, when connecting power from both, certain combinations could cause problems such as
unstable network connections. If a problem arises, disable one of the power supplies.
External Power Supply
12 V DC or 24 V AC input can be used. Use the included power interface cable to connect to
the camera power connection terminal.
1
3
1: BROWN Power 24 V AC / 12 V DC non-polar
2: BLUE Power 24 V AC / 12 V DC non-polar
3: GREEN FG (frame ground)
12 V DC can be connected in a non-polar configuration.
Important
The power supply should be within the following voltage range.
24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or 60 Hz ±0.5 Hz or less)
Current supply capacity of at least 1.0 A per camera
12 V DC: Voltage fluctuation within ±10% of 12 V DC
Current supply capacity of at least 1.5 A per camera
When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 – 1.0
Ω/20 W
in series to the power line.
For an external power supply, use a double-insulated device.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Canon VB-M740E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Canon VB-M740E in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Canon VB-M740E

Canon VB-M740E Gebruiksaanwijzing - English - 287 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info