784914
10
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
Page 7
Getting Started
4. SET THE TEMPERATURE CONTROL to the desired temperature
between 38°C (100°F) and 40°C (104°F), then place the spa
cover on the spa and allow the water temperature to stabilize
(approximately 24 hours). Make sure you secure the cover in place
using the cover locks. Periodically check the spa water temperature.
When the water temperature climbs above 32°C (90°F), proceed
to the next step. The spa temperature is pre-programmed to reach
38°C (100°F), and will normally do so within 18 to 24 hours. You may
change the water temperature by pressing the OPTION hard button
then press the soft button next to Temperature, (press soft button
next to
on the control panel to raise the temperature, or lower
temperature by pressing soft button next to ▼). After a few hours,
the water temperature will remain within 1.5°C (3°F ) of your selected
temperature.
5. USING A TEST STRIP AND APPLICABLE CHEMICALS adjust
Total Alkalinity (TA) to 80 ppm, Calcium Hardness (CH) between
75 - 150 ppm (if using Salt System between 25 - 75 ppm), then
spa water pH to between 7.4 and 7.8. These procedures are listed in
the “Water Quality and Maintenance” section.
OPERATION NOTE: Adjusting the Total Alkalinity as the first step is
important, as out-of balance TA will affect your ability to adjust the pH
correctly and will prevent the sanitizer from operating effectively.
When using the FRESHWATER Salt system the Calcium Hardness
must be between 25 - 75 ppm, if hardness is above 75 ppm use
VANISHING ACT (see pg. 11).
IMPORTANT: Activate the Clean cycle (Press the soft button next
to CLEAN on the home screen) before adding spa water chemicals
directly into the filter compartment. Make sure all diverter valves are
set to the middle position.
6. SUPERCHLORINATE THE SPA WATER by adding 1½ teaspoons
of FRESHWATER chlorine (sodium dichlor) per 950 liters (250
gallons) of spa water, then activate the Clean cycle.
7. TEST THE SPA WATER FOR CHLORINE RESIDUAL. If the
residual is between 1 and 5 ppm on the test strips, go on to the next
step. If the residual is less than 1 ppm, activate the Clean cycle, and
then retest, add more chlorine as necessary.
WARNING: High sanitizer levels can cause discomfort to the user’s
eyes, lungs and skin. Always allow the sanitizer level to fall to the
recommended range before using the spa.
8. RECHECK the Total Alkalinity (TA) 40 - 120 ppm, Calcium
Hardness (CH) 75 - 150 ppm (25 - 75 ppm with salt), then spa water
pH between 7.2 and 7.8.
OPERATION NOTE: Make sure you adjust your Total Alkalinity and
pH correctly, this will affect
the sanitizers effectiveness.
The spa is ready for use when the spa water has circulated and
the chlorine level remains between 1 and 5 ppm.
OPERATION NOTE: For proper water circulation during the ten-minute
Clean cycle the following steps should be performed.
Place the diverter valve in the middle (split flow) position
Place air control levers in OFF position by rotating clockwise
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Caldera Paradise - serie 2022 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Caldera Paradise - serie 2022 in de taal/talen: Engels als bijlage per email.

De handleiding is 6.53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Caldera Paradise - serie 2022

Caldera Paradise - serie 2022 Gebruiksaanwijzing - Nederlands - 44 pagina's

Caldera Paradise - serie 2022 Gebruiksaanwijzing - Deutsch - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info