784914
9
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
Page 6 Getting Started
WATERFALL VALVE
The SALINA, MAKENA, MARTINIQUE,
SEYCHELLES & REUNION spas are equipped
with a cascading waterfall feature. It is activated by
pressing the "JETS" button and turning the valve
located on the front interior wall counterclockwise.
The flow is regulated by turning the waterfall valve
to the desired position.
AIR CONTROLS
Each jet system has its own air
control. These allow you to change
the power of the jets by regulating the
amount of air that is mixed with the
water coming out of the jets.
QUICK START-UP INSTRUCTIONS
BEFORE YOU FILL YOUR SPA
Make sure your spa has been properly installed per all local codes, this
includes the location of the spa, the foundation of the spa as well as
the electrical installation of the spa. Installation instructions in the form
of a Pre-Delivery Instruction booklet can be obtained from either your
CALDERA dealer or online.
DO:
Know which water treatment system you will be using and make sure
you have necessary chemicals available. Read all of the instructions
that come with the system.
Have FRESHWATER 5-way Test Strips Available.
Have FRESHWATER Salt Test Strips Available if using the Salt system.
Have pH/Alkalinity Up & Down available.
Know the "Hardness" of your water, contact your dealer to help you
with this information. See Water Quality and Maintenance for more
information.
IMPORTANT: The spa can be filled with “softened” water as long as
the calcium hardness parameters (pg. 2) are maintained.
Purchase the Clean Screen pre-filter to remove unwanted
contaminants from the tap water. This is recommended, not required.
DON'T:
Power up the spa until it has been filled with water! Power to the
spa automatically activates critical components within the spa, such
as controls, heater, circulation pump, and other systems. If power
is supplied to these components prior to the spa being filled, the
components will be damaged, and this may result in a non-warranty
component failure.
Fill the spa with hot water or cold water with the cold water temperature
below 10º C (50º F)! Tripping of the high-limit thermostat may result
causing your spa to stop functioning.
START-UP
Your CALDERA spa has been thoroughly tested during the
manufacturing process to ensure reliability and long-term customer
satisfaction. A small amount of water may have remained in the
plumbing after testing and, as a result, may have spotted the spa shell
or the spa siding prior to delivery. Before filling the spa, wipe the spa
shell clean with a soft rag. The following instructions must be read and
followed exactly to ensure a successful start-up or refill.
CAUTIONS
Do NOT fill the spa with hot water, as tripping of the high-limit
thermostat may result.
DO NOT CONNECT POWER TO AN EMPTY SPA. Power to the
spa automatically activates critical components within the spa, such
as controls, heater, and other systems. If power is supplied to these
components prior to the spa being filled, the components will be
damaged, and this may result in a non-warranty component failure.
DO NOT use your spa after filling until all of the steps listed below are
completed.
DO NOT add chlorine if treating your spa with polyhexamethylene
biguanide (Biguanide, PHMB, eg. BaquaSpa
®) sanitizer.
Before filling your spa for the first time, remove the equipment
compartment door and check to ensure that the unions on either side
of the pump(s) and heater are hand-tight.
Door Panel Removal - see inside back cover:
a. Remove the 2 screws on the bottom of each corner.
b. Find notches in bottom of panel, place fingers on one side
and center notch. Slightly pull on bottom side panel to release 1st
clip. Move over to other side and center notch and pull on bottom
to release 2nd clip, then lower and remove panel.
1. CLOSE DRAIN, remove the filter compartment cover, skimmer
basket, weir, and filter. Fill your spa through the filter compartment
using the CLEANSCREEN pre-filter that attaches to your garden
hose. The water level of your spa should be maintained at a level
2.5 cm above the highest jet in the spa. Reinstall the filter and then
the skimmer basket, and weir once the spa is filled.
2. AFTER THE SPA HAS BEEN FILLED with water and the
equipment compartment door is secured, power must be applied
to the spa.
FIRST activate power to the subpanel from the main house
panel.
NEXT open the door of the electrical subpanel and reset the RCD
breaker.
FINALLY, close and secure the subpanel door.
3. TO CHECK THE OPERATION OF THE JET SYSTEM and to
purge any remaining air from the heating system complete the
following steps:
Press the soft button next to Jet Max to place both jet pumps on
High.
Once the jet system is fully operational (as indicated by strong,
non-surging jets), priming of the spa is complete
To turn off the jets, press
the soft button next to All Off on the
home screen
to turn all functions off simultaneously
If you do not feel a steady stream of water from your jets,
refer to the instructions for priming the pump in the SPA
TROUBLESHOOTING section.
IMPORTANT: Be sure that the diverter is in the middle position.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Caldera Paradise - serie 2022 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Caldera Paradise - serie 2022 in de taal/talen: Engels als bijlage per email.

De handleiding is 6.53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Caldera Paradise - serie 2022

Caldera Paradise - serie 2022 Gebruiksaanwijzing - Nederlands - 44 pagina's

Caldera Paradise - serie 2022 Gebruiksaanwijzing - Deutsch - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info