718772
183
Verklein
Vergroot
Pagina terug
1/212
Pagina verder
TROUBLESHOOTING
181
Appendix
7
k
Slightly lift up the needle plate, cut any tangled
threads, and then remove the needle plate.
Remove the fabric and threads from the needle plate.
l
Remove any threads in the race and around the feed
dogs.
m
Turn the handwheel to raise the feed dogs.
n
Align the two screw holes in the needle plate with the
two holes at the needle plate mounting base, and then
fit the needle plate onto the machine.
o
Lightly finger-tighten the screw on the right side of the
needle plate. Then, use the disc-shaped screwdriver to
firmly tighten the screw on the left side. Finally, firmly
tighten the screw on the right side.
p
Replace the bobbin case and the needle plate cover
following steps
h through j in “Cleaning the Race”.
q
Check the condition of the needle, and then install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
* Refer to “CHANGING THE NEEDLE” on page 48.
Checking Machine Operations
If the needle plate has been removed, check machine
operations to confirm that installation has been completed
correctly.
a
Turn on the machine.
b
Select .
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to check
that the needle falls at the center of the opening in the
needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with step
m in “Removing the Fabric From the Machine” on
page 180.
d
Select zigzag stitch . At this time, increase the
stitch length and width to their maximum settings.
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle bar and
feed dogs operate correctly.
Turn the handwheel to check that the feed dogs move
smoothly and do not contact the edges of the slots in the
needle plate.
1 Correct position of feed dogs
2 Incorrect position of feed dogs
f
Turn off the machine, and then install the presser foot
holder, presser foot and bobbin.
Never use a scratched or damaged presser foot.
Otherwise, the needle may break, or machine
performance may suffer.
* Refer to “Setting the Bobbin” on page 40 and
“CHANGING THE PRESSER FOOT” on page 50.
g
Correctly thread the machine.
* For details on the machine, refer to “UPPER
THREADING” on page 42.
h
Perform trial sewing with normal fabric.
If the fabric cannot be removed, even after
completing these steps, contact your nearest
Brother authorized service center.
Since the needle may have been damaged when
the fabric was caught in the machine, we
recommend replacing it with a new one.
Do not yet install the presser foot and thread.
1 Opening in the needle
plate
2 Handwheel
If the needle or feed dogs contact the needle plate,
the machine may be malfunctioning; therefore,
contact your nearest Brother authorized service
center.
Incorrect sewing may be the result of incorrect
upper threading or sewing thin fabrics. If there are
poor results from the trial sewing, check the upper
threading or the type of fabric being used.
a
b
a
b
183

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother Brother Innov-is XJ1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother Brother Innov-is XJ1 in de taal/talen: Engels als bijlage per email.

De handleiding is 12,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Brother Brother Innov-is XJ1

Brother Brother Innov-is XJ1 Gebruiksaanwijzing - Nederlands - 212 pagina's

Brother Brother Innov-is XJ1 Gebruiksaanwijzing - Deutsch - 212 pagina's

Brother Brother Innov-is XJ1 Gebruiksaanwijzing - Français - 212 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info