27
25
28
11 26
25
11
29
29
07
11
11
11
25
27
28
03
04
1. PREPARATORY STEPS
1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.
1.2 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.
2. Place the child seat facing forward on an approved car seat.
Make sure that the backrest 30 is flush with the backrest of
the car seat.
Tip! If the headrest of the car seat prevents the child seat
from being fastened properly, it should be removed (see
vehicle’s instruction manual). Secure the removed headrest
in a suitable place in the vehicle so that it will not be tossed
around.
1. PREPARATORY STEPS
1.1 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.
3. FASTENING THE ISOFIX
3.1 Position the two ISOFIX locking arms 04 directly in front of
the two insertion aids 02 .
3.2 Push the two ISOFIX locking arms 04 into the insertion aids
02 until the ISOFIX locking arms 04 engage on both sides
with an audible click.
DANGER! The green locking button 05 must be visible on
both sides indicating that the child seat is correctly fastened.
The
ADVANSAFIX M i-SIZE
is not permanently installed in the vehicle. It is simply
secured along with your child by the vehicle’s 3-point seat belt.
To adjust the seat angle:
Pull the adjustment handle 23 forwards and push/slide
the seat pan 24 into the desired position.
DANGER! The seat pan 24 PXVWEH¿UPO\HQJDJHG
whatever the position. Pull on the seat pan 24 to check
that it has engaged.
TIP! You can adjust the tilt angle of the child seat 24 even
while your child is sitting on it. Tighten the vehicle seat
belt after adjusting the seat angle if you use the child seat
with the vehicle seat belt (B1 and B2).
7. SECURING YOUR CHILD
4. PRESSING THE CHILD SEAT BACKWARDS
Push the child seat firmly backwards as far as it will go.
5. CHECKING FOR CORRECT FASTENING
Shake the child seat to check that it is securely fastened
and check the locking buttons 05 to make sure that the two
indicators are fully green.
6. Follow the steps in Section 7 “SECURING YOUR CHILD”.
2. Place the child seat on the car seat. Ensure that the back-
rest 30 is flat against the backrest of the car seat.
Tip! If the headrest of the car seat prevents the child seat
from being fastened properly, it should be removed (see
vehicle’s instruction manual). Secure the removed headrest
in a suitable place in the vehicle so that it will not be tossed
around.
3. Follow the steps in Section 7 “SECURING YOUR CHILD”.
A properly adjusted headrest 07 ensures optimal protection for
your child on the child seat. Regularly check that the height of
the headrest 07 is suitable for the body height of your child:
The headrest 07 must be adjusted so that the shoulder straps
08 are at the same level as your child’s shoulders, or slightly
higher.
A correctly adjusted headrest 07 ensures that the diagonal
belt 11 is optimally positioned and gives your child optimum
protection. Regularly check that the height of the headrest 07 is
suitable for the body height of your child:
The headrest 07 must be positioned so that two fingers can be
inserted between the headrest 07 and your child's shoulders.
To adjust the height of the headrest to fit your child:
1. Press and hold the adjustment handle 10 on the back ofthe
headrest 07 .
2. The headrest
07 is now unlocked and can be moved to the
desired height. When you release the adjustment handle 10 ,
the headrest 07 locks into place.
3. Place the child seat on the car seat.
4. Sit your child on the child seat and check the height.
Repeat this procedure until the headrest 07 is at thecorrect
height.
1. If your vehicle is not fitted with ISOFIX insertion aids
as standard, clamp the two insertion aids 02 (which
are supplied along with the seat*), with recess facing
upwards, into the two ISOFIX fixing points 01 in your
vehicle.
TIP: The ISOFIX fixing points are located between
theseat surface and the backrest of the car seat.
2. Move the headrest of the car seat to its topmost position.
3. Pull the grey handle 03 at the back of the child seat until
the ISOFIX locking arms 04 are fully extended.
4. On both sides of the ISOFIX locking arms, squeeze the
04 green locking button 05 and the red release button
06 together. This ensures that both hooks on the ISOFIX
locking arms 04 are open and ready to use.
* The insertion aids make it easier to install the child seat using the ISOFIX fixing points and they
prevent damage to the car seat covers. If they are not being used, remove them and keep them
in a safe place. For vehicles with a folding backrest, the insertion aids need to be removed before
folding the backrest.
Any problems that occur are usually caused by dirt or external objects on the insertion aids and
onthe hook. Remove the dirt or external objects to resolve such problems.
4.1 Preparing ISOFIX
First please read the section describing the desired installation method in Section 5.
ŹThe shoulder straps 08 must be adjusted so that they arehori-
zontal or just above your child’s shoulders.
ŹThe shoulder straps 08 must not be passed behind the child’s
back, or placed level with or above the child’s ears.
The shoulder straps are adjusted as follows:
1. Loosen the 5-point harness 09 on the child seat as far
aspossible.
2. Press and hold the adjustment handle 10 on the back ofthe
headres t07 .
3. The unlocked headrest 07 can now be moved to the desired
height. When you release the adjustment handle 10 , the
headrest 07 locks into place.
4. PREPARATORY STEPS
6. ADJUSTING THE SEAT ANGLE
100 - 150 cm
With car seat belt
B2
100 - 150 cm
With ISOFIX + car seat belt
B1 The seat shell of the
ADVANSAFIX M i-SIZE
FDQEHXVHGLQWKUHHGLႇHUHQWUHFOLQHG
positions. The
ADVANSAFIX M i-SIZE
is approved for use as follows:
Seat angle Body height
Upright position 76 - 140 cm
Middle position 76 - 150 cm
Lying position 76 - 150 cm
4.3 Adjusting the headrest (100 - 150 cm)
4.2 Adjusting the headrest (76 - 102 cm / ≤ 21 kg)
1. PREPARATORY STEPS
1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.
1.2 Follow the steps in Section 4.2 “ADJUSTING THE HEADREST (76 - 102 cm /
≤ 21kg)”.
76 - 102 cm / ≤ 21 kg
With ISOFIX + Top Tether
A
2. PREPARING THE TOP TETHER
2.1 Unhook the snap-on hook 12 of the top tether 13 from the
fastening on the back of the child seat.
3. FIXING THE TOP TETHER
Attach the snap-on hook 12 to the anchorage point recom-
mended in your vehicle's instruction manual.
CAUTION! Check that you are not using luggage hooks
instead of the top-tether anchorage points.
Look for the following symbol in your vehicle:
4. FASTENING THE ISOFIX
4.1 Position the two ISOFIX locking arms 04 directly in front of
the two insertion aids 02 .
4.2 Push the two ISOFIX locking arms 04 into the insertion aids
02 until the ISOFIX locking arms 04 engage on both sides
with an audible click.
DANGER! The green locking button 05 must be visible on
both sides indicating that the child seat is correctly fastened.
5. PRESSING THE CHILD SEAT BACKWARDS
Push the child seat firmly backwards as far as it will go.
6. CHECKING FOR CORRECT FASTENING
Shake the child seat to check that it is securely fastened
and check the locking buttons 05 to make sure that the two
indicators are fully green.
7. TIGHTENING THE TOP TETHER
Tighten the top tether 13 , until the belt tension indicator 16
turns green and the top tether 13 is tight.
2.2 Take the top tether 13 out of the pouch 14 and lay it over
the child seat.
2.3 Place the child seat in the direction of travel on an ap-
proved car seat. Adjust the backrest angle of the car seat
so that the gap between the car seat and the child seat is
as small as possible.
2.4 Take the top tether 13 and press the metal tongue 15
away from the belt to extend it, and pull the top tether 13
at the snap-on hook 12 .
2.5 Guide the top tether 13 in the middle between the bars of
the headrest 07 , for integrated headrests on the side closer
to the top tether 13 anchorage point of the vehicle.
8. LOOSEN THE SHOULDER STRAPS
To loosen the shoulder straps, press the adjustment button
18 while at the same time pulling both shoulder straps 08
forward.
CAUTION! Do not pull the shoulder cushions 19 .
9. OPEN THE HARNESS BUCKLE
To open the harness buckle 20 press the red button onthe
buckle.
10. SET THE CHILD IN THE CHILD SEAT
Place your child in the child seat.
Check that the harness buckle 20 is facing forwards.
11. PLACE THE SHOULDER STRAPS
Pass the shoulder straps 08 over your child’s shoulders.
WARNING! Do not twist or swap the shoulder straps, as this
will remove their protective function.
12. FASTENING THE HARNESS BUCKLE
Take the two buckle clips 21 and hold them together before
inserting them in the harness buckle 20 – they must make an
audible click when inserted.
13. TIGHTENING THE ADJUSTMENT STRAP
Pull the adjustment strap 22 until the strap lies flat andsnug
around your child’s body.
WARNING! The hip belts must be positioned aslowas possi-
ble across your child's hips.
Before each journey, in order to ensure your child’s safety, make
sure that ...
Źthe child seat is engaged on both sides with the ISOFIX locking arms 04
intheISOFIX fixing points 01 and that both locking buttons 05 are fully green;
Źthe child seat is securely fastened;
Źthe top tether 13 is tight over the backrest of the car seat and the belt tension
indicator 16 is green;
Źthe child seat belts fit snugly around the child’s body without causing constriction;
Źthe shoulder straps 08 are correctly adjusted and are not twisted;
Źthe shoulder cushions 19 are in the correct position for your child’s body;
Źboth buckle clips 21 are fully engaged in the harness buckle 20 ;
1. Sit your child in the child seat. Pullout the car seat belt,
pass it in front of your child and into the car seat belt buckle
27 .
DANGER! Check that the car seat belt is not twisted,
otherwise the full protective action of the restraint system
will be impaired.
Before every journey, for your child’s safety, check that ...
Źthe child seat is engaged on both sides with the ISOFIX locking arms in the
ISOFIX fixing points and both locking buttons are fully green (only applies to B1 |
with ISOFIX and car seat belt);
Źthe child seat is securely fastened;
Źthe lap belt is passed through the dark green belt guides on both sides of the
seat cushion,
Źthe
lap belt is passed through the dark green
SecureGuard.
Źthe diagonal belt on the car’s seat belt buckle side is also passed through the
dark green belt guide on the seat cushion,
Źthe diagonal belt is passed through the light green belt holder at the headrest,
DANGER!
If your child tries to open the car’s seat belt buckle 27 or insert the
diagonal belt 11 in the dark green SecureGuard 26 , stop your vehicle immedi-
ately, or as soon as possible. Check that the child seat is correctly fastened and
that your child is correctly secured. Explain to your child the dangers caused by
such actions.
2. Insert the buckle clip in the car seat belt buckle 27 until there
is an audible click.
3. Pass the diagonal belt 11 and lap belt 25 on the car’s seat-
belt buckle side 27 into the dark green belt guide 28 on the
seat cushion.
DANGER! The car’s seatbelt buckle 27 must not be near
the dark green belt guide 28 .
4. Also pass the lap belt 25 on the other side of the seat cush-
ion into the dark green belt guide 28 .
DANGER! The lap belt 25 must be placed as low as possi-
ble over your child’s hips on both sides.
5. Pass the lap belt 25 into the dark green SecureGuard 26 .
DANGER! Do not pass the diagonal belt 11 into the dark
green SecureGuard 26 .
6. Pass the diagonal belt 11 into the light green belt holder
29 at the headrest 07 so that it is fully in the belt holder 29
without twisting.
Tip! If the backrest 30 is covering the light green belt
holder 29 , you can adjust the headrest 07 upwards. The
diagonal belt 11 can then be easily inserted. You can then
adjust the headrest 07 back to the correct height.
7. Make sure that the diagonal belt 11 passes over the collar-
bone, not the neck, of your child and that the button on the
dark green belt holder is 29 fully closed.
Tip: You can adjust the height of the headrest 07 again in
the vehicle.
DANGER! The diagonal belt 11 must run diagonally back-
wards. You can adjust the belt routing with the adjustable
belt deflector in the vehicle.
DANGER! The diagonal belt 11 must never run forwards
towards the belt deflector on the vehicle. In this case, use
the child seat on the back seat only.
8. Tighten the car seat belt by pulling on the diagonal belt 11 .
5. INSTALLATION & USE
DANGER! Remove the child seat from the vehicle. Never carry the child seat in
the car if it is not fastened properly.
A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER)
1. Loosen the top tether 13 by pushing the metal tongue 15
away from the belt.
2. Release the snap-on hook 12 from the anchorage point in the vehicle and lay the
top tether 13 to the front over the child seat.
3. Loosen the ISOFIX fastening on both sides by squeezing the green locking button
05 and red release button 06 together.
4. Pull the seat forward and store the top tether 13 in the storage pouch 14 and
attach the snap-on hook of the top tether 13 to the fastening on the back of the
child seat.
5. Move the ISOFIX locking arms 04 back into the seat pan 24 .
B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)
1. Press the release button on your car seat buckle
2. Open the light green belt holder 29 by pressing the button on the belt holder 29
backwards, then pull out the diagonal belt 11 .
Only for installation method with ISOFIX:
3. To release the ISOFIX fitting, squeeze the green locking button 05 and red release
button 06 together, first on one side then on the other.
4. Move the ISOFIX locking arms 04 back into the seat pan 24 .
8. REMOVING THE CHILD SEAT
8.1 UNFASTENING YOUR CHILD:
8.2 REMOVAL:
A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER)
To unfasten your child, press the red button on the buckle.
B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)
To unfasten your child, use the release button of your car seat buckle.
Źthe diagonal belt runs diagonally backward,
Źthe straps are tight and not twisted,
Źthe car’s seat belt buckle is not placed in the dark green belt guide on the seat
cushion.
