504770
15
Verklein
Vergroot
Pagina terug
1/87
Pagina verder
English | 15
Bosch Power Tools 2 609 140 909 | (5.7.12)
ture in line a, the calculated dew point temperature in line c
and the measured surface temperature in line l.
The measuring tool automatically compares the values and in-
terprets the results as follows:
Green signal LED 8: No risk of mould under the current
conditions.
Yellow signal LED 8: The values are in the limit range; pay
attention to room temperature, humidity and heat bridges,
and repeat the measurement at a later point of time as re-
quired.
Red signal LED 8: There is an increased risk of mould, as
the dew point temperature is significantly higher than the
surface temperature, or because the humidity is too high.
The flashing symbol for relative humidity d indicates too
high humidity in the room,
the flashing symbol for ambient temperature e indicates
too low room temperature,
the flashing symbol for surface temperature h indicates
thermal bridges.
When the risk of mould is given, you should – depending on the
cause – reduce the humidity through more frequent and thor-
ough ventilation, increase the room temperature and eliminate
thermal bridges. If required, refer to a building expert.
Note: The measuring tool cannot detect mould spores. It only
indicates the possible formation of mould when the condi-
tions remain the same.
Troubleshooting Causes and Corrective
Measures
All of the following error messages in the display are accom-
panied by the red signal LED 8.
Measuring Tool not Acclimatized
The measuring tool was exposed
to severe variations in tempera-
ture and did not have enough time
to adapt.
The measuring tool switches off
automatically after 5 seconds.
Wait approx. 10 to 30 minutes
until the measuring tool has adapted to the current tempera-
tures. The acclimatization is accelerated when the measuring
tool is periodically moved around in the room.
Ambient Temperature not in Operating-temperature
Range
The ambient temperature is too
high or too low for operation of the
measuring tool. The measuring
tool switches off after 5 seconds;
taking measurements in this envi-
ronment is not possible.
Surface Temperature not within the Measuring Range
The surface temperature of the object in the laser circle is too
high (“Hi”) or too low (“Lo”). The temperature of this object
cannot be measured. Point the laser circle to another object
and start a new measurement.
Internal Error
The measuring tool has an inter-
nal error and switches off after
5 seconds.
To reset the software, remove the
batteries, wait a few seconds and
then insert the batteries again.
If the error continues, have the measuring tool checked by an
authorised Bosch after-sales service.
Definitions
Emissivity Degree
The emissivity degree of an object depends on the material
and the structure of its surface. It indicates whether an object
(in comparison with other objects with the same tempera-
ture) emits much or little infrared heat radiation.
Thermal Bridge
A thermal bridge is defined as an object that undesirably
transmits heat from one side to the other.
As the surface temperature at thermal bridges is lower than in
the rest of the room, the risk of mould increases significantly
at these locations.
Relative Humidity
The relative humidity provides information on how intensive
the air is saturated with water vapour. It is stated as a percent-
age of the maximum amount of water vapour that the air can
absorb. The maximum amount of water vapour depends on
the temperature: The higher the temperature, the more
amount of water vapour the air can absorb.
When the relative humidity is too high, the risk of mould in-
creases. Too low humidity can lead to health impairments.
Dew Point Temperature
The dew point temperature indicates the temperature at
which the water vapour in the air starts to condense. The dew
point temperature depends on the relative humidity and the
air temperature.
When the temperature of a surface is below the dew point
temperature, water begins to condense on this surface. The
larger the difference of both temperatures and the higher the
relative humidity, the greater the condensation.
Condensate on surfaces is a major cause for the formation of
mould.
Maintenance and Service
Maintenance and Cleaning
Store and transport the measuring tool only in the supplied
protective pouch 16. Do not, as an example, store the meas-
uring tool in a plastic bag, as the evaporation could damage
the humidity and temperature sensor 1. Do not attach stick-
ers onto the measuring tool close to the sensor.
OBJ_BUCH-1625-001.book Page 15 Thursday, July 5, 2012 8:56 AM
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PTD 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PTD 1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Noors als bijlage per email.

De handleiding is 8,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info