504770
14
Verklein
Vergroot
Pagina terug
1/87
Pagina verder
14 | English
2 609 140 909 | (5.7.12) Bosch Power Tools
The accuracy and reliability of the measuring results increase
with better and more stable measuring conditions.
The humidity and temperature sensor 1 can become dam-
aged through chemical contaminants, such as through the
evaporation of paints or enamels. The infrared temperature
measurement is affected through smoke, steam or dusty air.
Therefore, ventilate the room before measuring, especially
when the air is contaminated or steamy. For example, do not
apply a measurement in the bathroom directly after showering.
After ventilating, allow the room to acclimatize for a while until
the usual temperature has been reached again.
Ambient temperature and relative humidity are measured di-
rectly on the measuring tool via the humidity and temperature
sensor 1. To achieve substantial results, do not hold the
measuring tool directly above or next to interference sources
such as radiators or open liquids. Make sure not to cover off
the sensor 1.
Measuring Functions
Single Measurement
Briefly pressing the measuring button 4 once switches the la-
ser on and actuates a single measurement in the selected
mode.The measuring procedure can take 1 to 2 seconds and
is indicated through rotating display segments in line l.
The laser beam is switched off automatically upon completion
of the measurement.
The last measuring results are indicated on the display; the
“HOLD” m indicator flashes additionally. The signal LED re-
mains unchanged for the last indication.
Continuous Measurement (Tracking)
For continuous measurements, press and hold measuring
button 4 in the selected mode. The laser remains switched
on. Moving slowly, point the laser circle at all surfaces requir-
ing temperature measurement, one after the other. For hu-
midity and ambient-temperature measurements, slowly
move the measuring tool around in the room.
The display indication as well as the signal LED 8 are continu-
ously updated. As soon as releasing the measuring button 4,
the measurement is interrupted and the laser is switched off.
The last measuring results are indicated on the display; the
“HOLD” m indicator flashes additionally. The signal LED re-
mains unchanged for the last indication.
Surface-temperature-mode (see figure A)
In surface-temperature-mode, the surface temperature of an
object is measured.
To switch to surface-temperature-
mode, press the surface-tempera-
ture-mode button 11. The surface-
temperature-mode indicator k
appears on the display for confir-
mation.
Press measuring button 4 and point the laser circle perpen-
dicularly against the centre of the object being measured.
Upon completion of the measurement, the measured surface
temperature is displayed in line l.
In surface-temperature-mode, the signal LED 8 does not light
up.
This mode, as an example, is suitable for measuring the temper-
ature of radiators, underfloor heating systems or refrigerator
interiors.
Thermal-bridge-mode (see figure B)
In thermal-bridge-mode, surface and ambient temperature
are measured and compared with each other. In case of larger
differences between both temperatures, a thermal-bridge
warning is indicated (see “Thermal Bridge”, page 15).
To switch to thermal-bridge-
mode, press the thermal-bridge-
mode button 10. The thermal-
bridge-mode indicator j appears
on the display for confirmation.
Press measuring button 4 and
point the laser circle perpendicu-
larly against the centre of the object being measured. Upon
completion of the measurement, the measured surface tem-
perature is displayed in line l and the measured ambient tem-
perature in line a.
The measuring tool automatically compares the values and in-
terprets the results as follows:
Green signal LED 8: Low temperature difference, no ther-
mal bridges given.
Yellow signal LED 8: Temperature difference in limit
range; thermal bridge possible in the measuring range; re-
peat the measurement at a later point of time.
Red signal LED 8: The flashing symbol for surface tem-
perature h indicates that the surface temperature within
the measuring surface significantly deviates from the am-
bient temperature. A thermal bridge is in the measuring
range, which indicates poor insulation.
When the ambient temperature is low, the symbol for am-
bient temperature e additionally flashes. The room is too
cold when being normally heated, the low temperature
indicates an overall poor insulation.
In case of thermal bridges, check the insulation in this area,
perhaps with the support of a building expert.
Mould-warning-mode (see figure C)
In mould-warning-mode, the ambient temperature and the
relative humidity (see “Relative Humidity”, page 15) are
measured. The dew point temperature is calculated based on
both values (see “Dew Point Temperature”, page 15). In addi-
tion, the surface temperature is also measured.
The dew point temperature is compared with the surface tem-
perature and the result is interpreted as to the risk of mould.
To switch to mould-warning-
mode, press the mould-warning-
mode button 12. The mould-warn-
ing-mode indicator i appears on
the display for confirmation.
Press measuring button 4 and
point the laser circle perpendicu-
larly against the centre of the object being measured. Upon
completion of the measurement, the measured relative hu-
midity is displayed in line b, the measured ambient tempera-
OBJ_BUCH-1625-001.book Page 14 Thursday, July 5, 2012 8:56 AM
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PTD 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PTD 1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Noors als bijlage per email.

De handleiding is 8,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info