460547
21
Verklein
Vergroot
Pagina terug
1/152
Pagina verder
English | 21
Bosch Power Tools 2 609 004 157 | (11.5.10)
Assembly
Battery Charging
f Use only the battery chargers listed on the
accessories page. Only these battery charg-
ers are matched to the lithium ion battery of
your power tool.
Note: The battery is supplied partially charged.
To ensure full capacity of the battery, complete-
ly charge the battery in the battery charger be-
fore using your power tool for the first time.
The lithium ion battery can be charged at any
time without reducing its service life. Interrupt-
ing the charging procedure does not damage the
battery.
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
Removing the Battery
To remove the battery 2, press the unlocking
buttons 1 and pull the battery out of the ma-
chine to the rear. Do not exert any force.
Battery Charge-control Indication
When the power tool is switched on, the battery
charge-control indicator 4 signals the still avail-
able battery capacity or an overload.
When the battery charge-control indicator 4
flashes red, the machine is subject to overload.
Please observe the information in section “Tem-
perature-dependent Overload Protection”,
page 25.
Changing the Tool
f Before any work on the machine itself (e.g.
maintenance, tool change, etc.) as well as
during transport and storage, remove the
battery from the power tool. There is danger
of injury when unintentionally actuating the
On/Off switch.
f Wear protective gloves when changing ap-
plication tools/accessories. Contact with
the application tool/accessoriy can lead to
injuries.
Selecting the Application Tool/Accessory
The following table shows examples for application tools. Further application tools can be found in
the extensive Bosch accessories program.
Indication Capacity
Continuous lighting, green >70 %
Continuous lighting, yellow 3070 %
Continuous lighting, red <30 %
Accessory Material Application
BIM segment
saw blade
Wooden materials,
plastic, non-ferrous
metals
Separating and plunge cuts; also for sawing
close to edges, in corners and hard to reach
areas;
Example: shortening already installed bottom
rails or door hinges, plunge cuts for adjusting
floor panels
Base plate for
sanding, se-
ries Delta
93 mm
Depends on sand-
ing sheet
Sanding surfaces close to edges, in corners
or hard to reach areas;
Depending on the sanding sheet for, e.g.,
sanding wood, paint, varnish, stone
HCS plunge
cut saw blade,
wood
Wooden materials,
soft plastics
Separating and deep plunge cuts; also for
sawing close to edges, in corners and hard to
reach areas;
Example: narrow plunge cut in solid wood for
installing a ventilation grid
OBJ_BUCH-1170-002.book Page 21 Tuesday, May 11, 2010 3:36 PM
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PMF 10,8 LI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PMF 10,8 LI in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 10,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info