697319
15
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
Mounting | 15
6 720 816 739 (2015/05)MC 400
General information regarding the extra-low voltage side
All low voltage leads must be routed separately from cables carrying
mains voltage to avoid inductive interference (minimum separation
100 mm).
In the case of external inductive interferences (e.g. from PV
systems), use shielded cables (e.g. LIYCY) and earth the shield on
one side. The shield should be connected to the building's earth lead,
e.g. to a free earth conductor terminal or water pipe, and not to the
terminal for the earth lead in the module.
Route cables through the grommets provided and connect them as
shown in the connection diagrams.
3.2.2 Connecting the power supply, pump and mixer
(mains voltage side)
Only use electrical cables of the same quality.
Ensure that the power supply is connected to the correct phases.
A power supply via an earthed safety plug is not permitted.
Only connect components and assemblies to the outputs in
accordance with these instructions. Do not connect any additional
controls, which control other system components.
Route cables through the grommets, connect them as shown in the
connection diagrams and secure them with the strain reliefs, which
are supplied as part of the scope of delivery ( Fig. 11 to 18,
starting at page 83).
3.2.3 Connection diagrams with system schematics
The hydraulic diagrams are only schematic illustrations and provide a
non-binding notice of a possible hydraulic circuit. Install safety
equipment in accordance with applicable standards and local
regulations. For further information and options, refer to the technical
guides or tender specification.
Terminal designations (extra-low voltage side 24 V)
0-10 V Connection
1)
for 0-10 V room temperature-dependent controller
or building management system with a 0-10 V controller output, or
in addition for output feedback as a 0-10 V signal to terminal 3 for
a building management system
1) Terminal assignment: 1 – earth; 2 – 0-10 V input for heat requirement from the
building management system; 3 – 0-10 V output (optional) for feedback
BUS
2)
2) In a few devices, the terminal for the BUS system is labelled with EMS.
Connection to controller, modules
BUS1...4 Connection to heat sources or lower-level cascade modules
I2, I3 Connection to external switch (Input)
OC1 Connection
3)
Pump speed control with 0-10 V signal
(Cascade Output)
3) Terminal assignment: 1 - earth; 2 - output; 3 - input (optional)
T0, T1, T2 Temperature sensor connection (Temperature sensor)
Table 4
Terminal designations (mains voltage side)
120/230 V AC Mains voltage connection
PC0, PC1 Pump connection (Cascade Pump)
A0,I A1 Connection for fault display (Alert)
Table 5
The allocation of the electrical connections depends on the
system installed. The description shown in Fig. 12 to
Fig. 19, starting on page 83 onwards, is a possible
suggestion for making the electrical connection. The steps
are shown partly in different colours. This makes it easier to
see, which steps belong together.
The maximum power consumption of the connected
components and assemblies must not exceed the output
stated in the module specifications.
If the mains voltage is not supplied via the electronic
system of the heat source: install a standard all-pole
isolator (in accordance with EN 60335-1) on site to
interrupt the mains voltage.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch MC 400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch MC 400 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 4,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info