697319
14
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
14 | Mounting
MC 4006 720 816 739 (2015/05)
2.6 Additional accessories
For detailed information about suitable accessories, please refer to the
catalogue.
User interface: weather-compensated controller with outside
temperature sensor or room temperature-dependent controller;
connect to BUS (do not connect to BUS1, BUS2, BUS3 or BUS4);
connect outside temperature sensor to T1
Flow temperature sensor; connect to T0
Outside temperature sensor; connect to T1
Return temperature sensor; connect to T2
Cascade pump; connect to PC0
Heating pump; connect to PC1
Switch for max. output; connect to I2
Stop switch; connect to I3
IGM for heat source without EMS, EMS 2 or EMS plus; connect in
accordance with the technical documentation for the IGM (the
MC400 cascade module replaces the ICM)
Installation of additional accessories
Install the additional accessories in accordance with legal
requirements and the instructions supplied.
2.7 Cleaning
If required, wipe the enclosure with a damp cloth. Never use
aggressive or acidic cleaning agents for this.
3Mounting
3.1 Installation
Install the module on a wall, ( Fig. 6 to Fig. 8, starting at page 82),
on a mounting rail ( Fig. 9, page 82) or in an assembly.
When removing the module from the mounting rail, refer to Fig. 10 on
page 83.
3.2 Electrical connection
Observe current regulations applicable to power connections, and
use at least cable type H05 VV-…
3.2.1 Connecting the BUS connection and temperature sensor
(extra-low voltage side)
General BUS connection
Maximum total length of BUS connections:
100 m at 0.50 mm
2
conductor cross-section
300 m at 1.50 mm
2
conductor cross-section
BUS connection between the heat source – and cascade module
Connect the heat sources and lower-level cascade modules directly to
terminals
BUS1 ...BUS4
(
overview of the terminal assignment).
BUS connection between the cascade module – user interface
other modules
If the conductor cross-sections are different, use the junction box to
connect the BUS nodes.
BUS user [B] via junction box [A] in a star ( Fig. 19, page 84, note
the instructions for the user interface and other modules).
Temperature sensor
When sensor leads are extended, apply the following lead cross-sections:
up to 20 m with 0.75 mm
2
to 1.50 mm
2
conductor cross-section
20 m up to 100 m with 1.50 mm
2
conductor cross-section
Maximum output per connection
•PC0, PC1
•A0, IA1
400 W (high-efficiency pumps
permitted; max. 40 A/s)
•10W
Capturing range for the flow and
return temperature sensor
Lower fault limit
Display range
Upper fault limit
< – 10 °C
0 ... 100 °C
> 125 °C
Capturing range, outside
temperature sensor
Lower fault limit
Display range
Upper fault limit
< – 35 °C
– 30 ... 50 °C
> 125 °C
Permitted ambient temp. 0 ... 60 °C
IP rating IP44
Protection class I
ID no. Data plate ( Fig. 22, page 85)
Specifications
Table 3
DANGER: Risk of electric shock!
Before installing this product: completely disconnect
heat appliances and all other BUS nodes from the mains
voltage.
Before commissioning: fit the cover ( Fig. 21,
page 85).
If the maximum cable length of the BUS connection between
all BUS nodes is exceeded, or if the BUS system is realised
as a ring structure, the system cannot be commissioned.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch MC 400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch MC 400 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 4,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info