79075
25
Verklein
Vergroot
Pagina terug
1/156
Pagina verder
26 | English 1 609 929 L08 12.1.07
Reduced starting current
The electronic reduced starting current limits the
power consumption when switching the tool on and
enables operation from a 13 ampere fuse.
Constant Electronic Control
Constant electronic control holds the speed constant
at no-load and under load, and ensures uniform work-
ing performance.
Speed preselection (GWS 15-125 CIEH/GWS 15-125 CITH)
The required speed can be preselected with the thumbwheel 3 (also while running).
The data in the following table are recommended values.
Operating Instructions
f Exercise caution when cutting slots in struc-
tural walls; see Section “
Information on
Structures
”.
f Clamp the workpiece if it does not remain
stationary due to its own weight.
f Do not strain the machine so heavily that it
comes to a standstill.
f Grinding and cutting discs become very hot
while working; do not touch until they have
cooled.
Rough Grinding
f Never use a cutting disc for roughing.
The best roughing results are achieved when setting
the machine at an angle of 30° to 40°. Move the
machine back and forth with moderate pressure. In
this manner, the workpiece will not become too hot,
does not discolour and no grooves are formed.
Flap Disc
With the flap disc (accessory), curved surfaces and
profiles can be worked.
Flap discs have a considerably higher service life,
lower noise levels and lower sanding temperatures
than conventional sanding sheets.
Cutting Metal
f For cutting metal, always work with the pro-
tection guard for cutting 13.
When cutting, work with moderate feed, adapted to
the material being cut. Do not exert pressure onto the
cutting disc, tilt or oscillate the machine.
Do not reduce the speed of running down cutting
discs by applying sideward pressure.
The machine must
always work in an up-
grinding motion. Oth-
erwise, the danger
exists of it being
pushed uncon-
trolled out of the cut.
When cutting profiles
and square bar, it is
best to start at the
smallest cross sec-
tion.
Cutting Stone
f For cutting stone, always work with the cut-
ting guide with dust extraction protection
guard 20.
f The machine may be used only for dry cut-
ting/grinding.
For cutting stone, it is best to use a diamond cutting
disc. As a safety measure against jamming, the cutting
guide with dust extraction protection guard 20 must
be used.
Operate the machine only with dust extraction and
additionally wear a dust protection mask.
The vacuum cleaner must be approved for the extrac-
tion of masonry dust. Bosch provides suitable vacuum
cleaners.
Material Application Tool Thumbwheel 3
Metal Removing paint Sanding disc 2 3
Wood, metall Brushing, rust removal Cup brush, sanding disc 3
Metal, masonry Sanding Sanding disc 4 6
Metal Rough grinding Sanding disc 6
Masonry, stone Cutting Cutting disc and cutting guide
(Cutting masonry/stone is permitted
only with use of the cutting guide) 6
OBJ_BUCH-165-003.book Page 26 Friday, January 12, 2007 9:16 AM
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GWS 15-125 CITH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GWS 15-125 CITH in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Bosch GWS 15-125 CITH

Bosch GWS 15-125 CITH Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 156 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info