79075
24
Verklein
Vergroot
Pagina terug
1/156
Pagina verder
English | 251 609 929 L08 12.1.07
Approved Grinding Tools
All grinding tools mentioned in these operating
instructions can be used.
The permissible speed [rpm] or the circumferential
speed [m/s] of the grinding tools used must at least
match the values given in the table.
Therefore, observe the permissible rotational/cir-
cumferential speed on the label of the grinding tool.
Rotating the Machine Head
f Before any work on the machine itself, pull
the mains plug.
The machine head can
be rotated with respect
to the machine housing
in 90° steps. In this
manner, the On/Off
switch can be brought
into a more convenient
position for special
working situations,
e.g., for cutting opera-
tions using the cutting
guide with dust extrac-
tion protection guard
20/cut off stand or for
left-handed persons.
Completely unscrew the four screws. Rotate the
machine head carefully, without removing it from
the housing, to the new position. Screw in and
tighten the four screws again.
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
When operating the machine with power from mobile
generators that do not have sufficient reserve capacity
or are not equipped with suitable voltage control with
starting current amplification, loss of performance or
untypical behavior can occur upon switching on.
Please observe the suitability of the power generator
being used.
Switching On and Off
To start the power tool, press the On/Off switch 4
forward and then down.
To lock-on the pressed On/Off switch 4, push the
On/Off switch 4 further forward.
To switch off the power tool, release the On/Off
switch 4, or when it is locked, briefly press the On/Off
switch 4 and then release it.
Switch Version without Lock-on
(country-specific):
To start the power tool, press the On/Off switch 4
forward and then down.
To switch off the machine, release the On/Off switch
4.
f Check grinding tools before using. The
grinding tool must be mounted properly and
be able to move freely. Carry out a test run
for at least one minute with no load. Do not
use damaged, out-of-centre or vibrating
grinding tools. Damaged grinding tools can
burst and cause injuries.
Kickback stop
In case of a sudden drop in speed,
e. g. jamming while carrying out a sep-
arating cut, the power supply to the
motor is interrupted.
To restart the operation, switch the
On/Off switch 4 to the Off position
and start the machine again.
Restarting protection
The restarting protection feature prevents uncon-
trolled restarting of the machine after an interruption in
the power supply.
To restart the operation, switch the On/Off switch
4 to the Off position and start the machine again.
max.
[mm] [mm]
D b d [rpm] [m/s]
115
125
150
6
6
6
22,2
22,2
22,2
11000
11000
9300
80
80
80
115
125
––
11000
11000
80
80
75 30 M 14 11000 45
b
d
D
D
D
b
d
OBJ_BUCH-165-003.book Page 25 Friday, January 12, 2007 9:16 AM
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GWS 15-125 CITH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GWS 15-125 CITH in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Bosch GWS 15-125 CITH

Bosch GWS 15-125 CITH Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 156 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info