592525
15
Verklein
Vergroot
Pagina terug
1/85
Pagina verder
English | 15
Bosch Power Tools 1 609 929 N55 | (14.11.07)
Adjusting Cutter Clearance b
For adjustment of cutter
clearance b, the stroke
mechanism of the upper cut-
ter must be at the upper
dead centre point. For this,
briefly switch the power tool
on and then immediately off
again. If the stroke mechanism does not stop at
the upper dead centre point, repeat the process.
Screw the adjustment screw for the upper cutter
5 in clockwise direction using a fitting pin. Loos-
en the fastening screw for the upper cutter 8 and
adjust the upper cutter 7 in such a manner that
the vertical clearance b between upper and bot-
tom cutter is 0.4 mm. Check the clearance with
the setting gauge 13.
Retighten the fastening screw 8 for the upper
cutter. Screw the adjustment screw for the up-
per cutter 5 in anticlockwise direction until it fac-
es against the upper cutter 7.
For softer or more ductile materials, the
clearance b must be decreased; for harder or
more brittle materials, increased.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
Replacing the Bottom Cutter (see figure B)
Unscrew the adjustment screw 11 of the bottom
cutter. Fully unscrew the fastening screw 12 of the
bottom cutter and remove the bottom cutter 9.
Insert a new bottom cutter 9 into the recess of
the cutting base 10. Fasten the bottom cutter
with the fastening screw 12.
Check the cutter clearance a (see “Adjusting
Cutter Clearance a”, page 14).
Replacing the Upper Cutter (see figure B)
Both sides of the upper cutter 7 can be used.
Fully unscrew the fastening screw 8 of the upper
cutter and remove the upper cutter 7.
Turn the upper cutter 7 as shown in the figure or
place a new upper cutter against the striker 6.
Fasten the upper cutter with fastening screw 8.
Check the cutter clearance b (see “Adjusting
Cutter Clearance b”, page 15).
Regrinding the Cutters (see figure C)
Replace or regrind worn cutters in good time.
Only sharp tools achieve good cutting capacity
and make the machine last longer.
When regrinding the cutters, take care that the
cutting angles are maintained.
Check the cutting angles with the setting gauge 13.
WARNING! Important instructions for connect-
ing a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to
the following code:
Do not connect the blue or brown wire to the
earth terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this power tool, it
must be disposed of safely.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article number
given on the type plate of the machine.
b
OBJ_BUCH-598-001.book Page 15 Wednesday, November 14, 2007 10:16 AM
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GSC 2.8 Professional bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GSC 2.8 Professional in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info