592525
14
Verklein
Vergroot
Pagina terug
1/85
Pagina verder
1 609 929 N55 | (14.11.07) Bosch Power Tools
14 | English
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1
forward so that the “I” is indicated on the switch.
To switch off the machine, push the On/Off
switch 1 toward the rear so that the “0” is indi-
cated on the switch.
Working Advice
Apply the power tool to the workpiece only when
switched on.
Hold the power tool inclined in an angle of 15° to
the surface of the steel sheet and do not tilt it lat-
erally.
Guide the machine evenly and with light feed in
the cutting direction. Excessive feed significantly
reduces the service life of the saw blade and can
cause damage to the power tool.
f Wear protective gloves while working and
pay particular attention to the mains cable.
Sharp burrs develop at the cut steel sheet and
can cause injuries to the operator or damage
the mains cable.
When cutting curves, make sure not to tilt the pow-
er tool laterally and work with low feed rate only.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
max
depends on the strength properties of the ma-
terial to be cut.
The machine allows for cutting of metal sheet to
the following thicknesses:
Adjusting Cutter Clearance a
The cutter clearance a (gap be-
tween the cutters) depends on
the sheet thickness d
max
to be cut.
For softer or more ductile materials, the
clearance a must be decreased; for harder or
more brittle materials, increased.
Loosen the fastening screw 12 for the bottom
cutter. Adjust the requested cutter clearance a
with the adjustment screw 11. The upper cutter
7 and the bottom cutter 9 may not touch each
other. Check the clearance with the setting
gauge 13. Retighten the fastening screw 12 for
the bottom cutter.
15
˚
Material Max. strength property
[N/mm
2
]
d
max
[mm]
Steel 400 2.8
600 2.2
800 1.9
Aluminium 200 3.5
d
max
[mm]
Cutter clearance a
[mm]
0.2
1.4 0.3
1.5
2.8 0.5
a
OBJ_BUCH-598-001.book Page 14 Wednesday, November 14, 2007 10:16 AM
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GSC 2.8 Professional bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GSC 2.8 Professional in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info