592526
13
Verklein
Vergroot
Pagina terug
1/79
Pagina verder
English | 13
Bosch Power Tools 1 609 929 M52 | (1.4.09)
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data”
is in conformity with the following standards
or standardization documents: EN 60745 ac-
cording to the provisions of the directives
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 12.09.2007
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1
forwards.
To lock the On/Off switch 1, additionally push
down the front of the switch.
To switch off the machine, release the On/Off
switch 1. When the On/Off switch is locked, press
on the rear of the switch and then release it.
Working Advice
f The power tool is not suitable for stationary
operation. For example, it may not be
clamped in a vice or fastened on a workbench.
f Only work with the chip deflector 2 mount-
ed. Take care that the chip deflector is not
damaged or bent. Danger of injury when
working without the chip deflector or when it
is damaged. Have a damaged chip deflector
replaced immediately by an after-sales
service centre for Bosch power tools.
f Wear protective gloves while working and
pay particular attention to the mains cable.
Take care that cut sheet parts do not bend
toward your body or the mains cable. Sharp
burrs develop at the cut steel sheet and can
cause injuries to the operator or damage the
mains cable. If required, press bending steel
sheet parts away from your body or the
mains cable using gloves.
Apply the power tool to the workpiece only
when switched on.
Guide the power tool at an angle of 80 to 90° to
the surface of the sheet metal and do not tilt it
to the side.
Guide the machine evenly and with light feed in
the cutting direction. Excessive feed significantly
reduces the service life of the saw blade and can
cause damage to the power tool.
When cutting curves, make sure not to tilt the
power tool laterally and work with low feed rate
only.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
80–90
˚
OBJ_BUCH-460-002.book Page 13 Wednesday, April 1, 2009 3:34 PM
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GSC 160 Professional bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GSC 160 Professional in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Bosch GSC 160 Professional

Bosch GSC 160 Professional Gebruiksaanwijzing - Polski - 89 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info