544272
14
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
14 | English
1 609 929 N87 | (13.2.09) Bosch Power Tools
Place the power tool in such a manner on
both rear chaser rollers 3, that the diamond
cutting discs do not touch the workpiece.
Switch the machine on and slowly plunge in-
to the material.
Guide the machine with both handles, apply-
ing moderate feed, suited to the material be-
ing worked.
The machine must always work in an up-
grinding motion. Otherwise, the danger ex-
ists of it being pushed uncontrolled out of
the cut.
The machine can be both pushed or pulled in
the cutting direction. Vertical slots can easily
be cut by pulling the machine from top to
bottom.
After finishing the working procedure, swivel
the diamond cutting discs out of the slot with
the machine still running.
Switch the power tool off.
Do not brake coasting diamond cutting discs by
applying sideward pressure.
f Never set down a coasting machine on the
chaser rollers 3, but always aside, so that
the diamond cutting discs can rotate freely
and do not face toward your body.
f Diamond cutting discs become very hot dur-
ing operation; do not touch them until they
have cooled down.
Remove the remaining fin of the material with
the break-out tool 21.
Curved cuts are not possible, as the diamond
cutting discs could jam in the material.
When cutting through plate materials, ensure
that the materials are firmly backed on a surface
or supported.
When breaking through walls, e. g. with a rotary
hammer, most of the chipping-off of the surface
material can be avoided by first cutting in a slot
with maximum cutting depth.
For cutting expecially hard material, e. g., con-
crete with high pebble content, the diamond cut-
ting disc can overheat and become damaged as a
result. This is clearly indicated by circular spark-
ing, rotating with the diamond cutting disc.
In this case, interrupt the cutting process and al-
low the diamond cutting disc to cool by running
the machine for a short time at maximum speed
with no load.
Noticeable decreasing work progress and circu-
lar sparking are indications of a diamond cutting
disc that has become dull. Briefly cutting into
abrasive material (e. g. lime-sand brick) can re-
sharpen the disc again.
Information on Structures
Slots in structural walls are subject to the
Standard DIN 1053 Part 1, or country-specific
regulations.
These regulations are to be observed under all
circumstances. Before beginning work, consult
the responsible structural engineer, architect or
the construction supervisor.
The permitted slot depth and width depends on
the slot length, wall thickness and the building
material used.
21
OBJ_BUCH-916-001.book Page 14 Friday, February 13, 2009 11:21 AM
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GNF 65 A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GNF 65 A in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info