544272
13
Verklein
Vergroot
Pagina terug
1/105
Pagina verder
English | 13
Bosch Power Tools 1 609 929 N87 | (13.2.09)
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine.
Switching On and Off
f Before starting the machine, place the pow-
er tool in such a manner on both rear chaser
rollers 3 that the diamond cutting discs do
not touch the workpiece. Otherwise, the
diamond cutting discs can touch the work-
piece, resulting in possible loss of control
over the power tool when switching on.
To start the power tool, press the On/Off switch
1 forward and then down.
To lock-on the pressed On/Off switch 1, push
the On/Off switch 1 further forward.
To switch off the power tool, release the On/Off
switch 1, or when it is locked, briefly press the
On/Off switch 1 and then release it.
Switch Version without Lock-on
(country-specific):
To start the power tool, press the On/Off switch
1 forward and then down.
To switch off the machine, release the On/Off
switch 1.
f Never set down a coasting machine on the
chaser rollers 3, but always aside, so that
the diamond cutting discs can rotate freely
and do not face toward your body.
f Check the diamond cutting discs before
use. The diamond cutting disc(s) must be
mounted properly and be able to rotate
freely. Carry out a test run for at least one
minute without any load. Do not use dia-
mond cutting discs that are damaged, out-
of-balance, or vibrate. Damaged diamond
cutting discs can rupture and lead to injuries.
Reduced starting current
The electronic reduced starting current limits
the power consumption when switching the tool
on and enables operation from a 13 ampere
fuse.
Overload Protection
When overloaded, the motor comes to a stop.
Relieve the load on the machine immediately
and allow to cool down for approx. 30 seconds
at the highest no-load speed.
Restarting Protection
The restarting protection feature prevents un-
controlled restarting of the machine after an in-
terruption in the power supply.
To restart the operation, switch the On/Off
switch 1 to the Off position and start the ma-
chine again.
Note: Check the function of the restarting pro-
tection feature regularly by having the mains
plug pulled during operation and plugged in
again afterwards.
Working Advice
f Exercise caution when cutting slots in
structural walls; see Section “Information
on Structures ”.
f Do not strain the machine so heavily that it
comes to a standstill.
f Clamp the workpiece if it does not remain
stationary due to its own weight.
f The machine may only be used for dry cut-
ting.
f Always guide the machine with both han-
dles. Do not guide or carry the machine by
the elbow.
Adjust the cutting depth, see section “Pre-se-
lecting the Cutting Depth”. To compensate
inaccuracies that occur when breaking away
the fin, the cutting depth must be set approx.
3 mm deeper than the requested slot depth.
OBJ_BUCH-916-001.book Page 13 Friday, February 13, 2009 11:21 AM
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GNF 65 A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GNF 65 A in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 4,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info