78670
21
Verklein
Vergroot
Pagina terug
1/122
Pagina verder
English | 21
Bosch Power Tools 1 609 929 M67 | (12.11.07)
Adjusting the Speed
The speed of the switched on power tool can be
variably adjusted, depending on how far the
On/Off switch 9 is pressed.
Light pressure on the On/Off switch 9 results in
a low rotational speed. Further pressure on the
switch results in an increase in speed.
Swivel Lighting System (see figure C)
Your tool is equipped with a light source in the
knurled thumbwheel 7. The light is activated as
soon as the knurled thumbwheel 7 is in position
1
3 and the On/Off switch 9 is pressed.
Depending on the bit being used, the light beam
can be adjusted to three positions by turning the
knurled thumbwheel 7. In position 1, the focus of
the light beam is approx. 20 mm, in position 2 ap-
prox. 150 mm and in position 3 approx. 500 mm
in front of the tool holder 1.
In the “OFF” position, the light is switched off
permanently.
Working Advice
f Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts
can slip off.
The torque depends on the impact duration. The
maximum achieved torque results from the sum
of all individual torques achieved through impact.
The maximum torque is achieved after an impact
duration of 610 seconds. After this duration,
the tightening torque is increased only minimally.
The impact duration is to be determined for each
required tightening torque. The actually achieved
tightening torque is always to be checked with a
torque wrench.
Screw Applications with Hard, Spring-loaded or
Soft Seat
When in a test, the achieved torques in an impact
series are measured and transferred into a dia-
gram, resulting in the curve of a torque character-
istic. The height of the curve corresponds with
the maximum reachable torque, and the steep-
ness indicates the duration in which this is
achieved.
A torque gradient depends on the following fac-
tors:
Strength properties of the screws/nuts
Type of backing (washer, disc spring, seal)
Strength properties of the material being
screwed/bolted together
Lubrication conditions at the screw/bolt con-
nection
The following application cases result according-
ly:
–A hard seat is given for metal-to-metal screw
applications with the use of washers. After a
relatively short impact duration, the maximum
torque is reached (steep characteristic
curve). Unnecessary long impact duration on-
ly causes damage to the machine.
–A spring-loaded seat is given for metal-to-
metal screw applications, however with the
use of spring washers, disc springs, studs or
screws/nuts with conical seat as well as when
using extensions.
–A soft seat is given for screw applications,
e. g., metal on wood or when using lead wash-
ers or fibre washers as backing.
For a spring-loaded seat as well as for a soft seat,
the maximum tightening torque is lower than for
a hard seat. Also, a clearly longer impact duration
is required.
OBJ_BUCH-595-001.book Page 21 Monday, November 12, 2007 4:15 PM
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GDS 14,4 V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GDS 14,4 V in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info