786182
15
Verklein
Vergroot
Pagina terug
1/85
Pagina verder
English | 15
Fitting the Stabilising Brackets (seefigureA)
Push the stabilising bracket(11) all the way into the as-
sembly openings(22).
Fitting the Dust Extraction Attachment
(seefiguresB1−B2)
Ensure the dust extraction attachment is correctly
attached to the rotary hammer. Using the dust extraction
attachment reduces the risks posed by dust.
GDE 18V-26 D with GBH 2-26 (F) or GBH 2-28 (F):
Fit the stabilising bracket(11) on the dust extraction at-
tachment.
Remove the auxiliary handle of the rotary hammer.
Place the dust extraction attachment on a stable surface.
Put the front part of the rotary hammer down on the
mounting bracket(9).
Push the rotary hammer forwards into the clamping
ring(8), until you can hear the rotary hammer click into
place into both of the guide pins(10) and the locking
receptacle(6).
Make sure that the clamping ring(8) of the auxiliary
handle slots into the corresponding groove of the housing
on the rotary hammer.
Fit the lower gripping end of the auxiliary handle(7).
Swivel the auxiliary handle(7) around the axis of the
rotary hammer to the required position.
Turn the lower gripping end of the auxiliary handle(7)
clockwise to tighten it.
To loosen the rotary hammer from the dust extraction at-
tachment, loosen the clamping ring (8) by turning the
lower gripping end of the auxiliary handle (7) anticlock-
wise.
Push the locking tab (5) while pulling the rotary hammer
to the rear and pushing downwards at the same time.
Operation
Working advice
uNever use the dust extraction attachment without a
filter. If the dust extraction attachment is used without a
filter, larger particles of drilling dust can be flung towards
the user and the power tool can be damaged.
uDo not use damaged filters (e.g. no cracks, small
holes, etc.). Replace any damaged filters immedi-
ately.
uNever carry the power tool by the dust extraction at-
tachment.
Note: The guide(18) is spring-loaded. The guide can spring
forward when the button(17) for drill bit length adjustment
is pressed.
Switching On and Off
To switch on the dust extraction attachment, press the
on/off switch(14).
To switch off the dust extraction attachment, press the
on/off switch(14) again.
Inserting/removing the drill bit (seefigureC)
Press the button (17) for drilling depth adjustment and
pull the guide (18) all the way out.
Release the button (17) again.
Slide the tip of the drill bit through the dust cap (3) from
behind and then fit the bit into the drill chuck according to
the instructions of your power tool.
Before removing the drill bit, press the button (17) again
and pull the guide (18) all the way out.
Adjusting the Guide Length (seefigureD)
To ensure that dust is extracted cleanly and the depth stop is
set correctly, the guide(18) must be adjusted so that the tip
of the drill bit is flush at the front with the dust cap(1)/(3).
Insert the required drill bit into the
tool holder of the drill chuck.
Press the button(17) while adjust-
ing the guide(18) to match the drill
bit length.
Release the button(17) again.
Note: To store the dust extraction attachment, press the
button(17) and pull the guide(18) all the way out. This re-
lieves the strain on the guide's spring, which increases the
service life of the spring.
Adjusting the Drilling Depth (see figure E)
The button (19) for depth stop adjustment can be used to
set the required drilling depthX.
Press the button (19) and slide the button on the guide
(18) so that the distance X shown in the illustration
matches your required drilling depth.
Release the button (19) again.
Fitting the Dust Cap and Extension (seefigureF)
You will need to change the dust cap(1)/(3) depending on
which drill chuck you are using:
Dust cap(1) for SDS plus quick-change chuck for drilling
diameters of 4–16mm
Dust cap(2) for SDS plus quick-change chuck for drilling
diameters of 16–26mm
Dust cap(3) for SDS plus fixed chuck for drilling diamet-
ers of 4–16mm
Bosch Power Tools 1 609 92A 7YA | (11.07.2022)
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GDE 18V-26 D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GDE 18V-26 D in de taal/talen: Alle talen als bijlage per email.

De handleiding is 4.47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info