786259
21
Verklein
Vergroot
Pagina terug
1/337
Pagina verder
English | 21
Turn the lower gripping end of the auxiliary handle (16)
anticlockwise and swivel the auxiliary handle (16) into
the required position. Then turn the lower gripping end of
the auxiliary handle (16) clockwise to retighten it.
Make sure that the retaining strap of the auxiliary handle
slots into the corresponding groove of the housing.
Selecting drill chucks and tools
For hammer drilling and chiselling, you will need SDS plus
tools, which insert into the SDS plus drill chuck.
For drilling without impact in wood, metal, ceramic and
plastic as well as for screwdriving, tools without SDS plus
are used (e.g. cylindrical shank drill bits). For these tools,
you will need the keyless quick-change chuck(1) with integ-
rated impact stop.
Note: Using the keyless quick-change chuck(1) with integ-
rated impact stop is the only way to ensure that the tools in-
serted are not damaged.
Changing the drill chuck
Removing the Quick-Change Chuck (seefigureB)
Pull back on the quick-change chuck locking ring(6), hold
it in this position and pull the SDS plus quick-change
chuck(2) or the keyless quick-change chuck(1) out from
the front.
Once the quick-change chuck is removed, protect it from
dirt.
Inserting the Quick-Change Chuck (seefigureC)
Before insertion, clean the quick-change chuck and lightly
grease the shank.
Wrap your whole hand around the SDS plus quick-change
chuck(2) or the keyless quick-change chuck(1). Use a
turning motion to push the quick-change chuck into the
drill chuck holder(20) until you hear it click into place.
The quick-change chuck is automatically locked. Check
that it is locked by pulling on the quick-change chuck.
Changing the Tool
The dust protection cap (4) largely prevents the penetration
of drilling dust into the tool holder during operation. When
inserting the tool, make sure that the dust protection cap (4)
does not become damaged.
uReplace a damaged dust protection cap immediately.
It is recommended that you have use an after-sales
service for this.
Changing the tool (SDS plus)
Inserting SDS-plus application tools (seefigureD)
The SDS-plus drill chuck enables you to change the applica-
tion tool easily and conveniently without needing to use ad-
ditional tools.
Clean and lightly grease the insertion end of the applica-
tion tool.
Insert the application tool into the tool holder while turn-
ing it until it locks automatically.
Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus application
tool can move freely. This causes a certain radial run-out at
no-load, which has no effect on the accuracy of the drill hole,
as the drill bit centres itself upon drilling.
Removing SDS-plus application tools (seefigureE)
Push the locking sleeve (5) back and remove the applica-
tion tool.
Changing the keyless quick-change chuck
Inserting the Application Tool (seefigureF)
Note: Application tools that do not have SDS plus must not
be used for hammer drilling or chiselling. Tools without SDS
plus and their drill chucks are damaged by hammer drilling
or chiselling.
Insert the keyless quick-change chuck(1) with integrated
impact stop.
Note: Only use the keyless quick-change chuck with integ-
rated impact stop specifically designed for the
GBH18V-34CF. Using this drill chuck is the only way to en-
sure that the pneumatic impact mechanism of the rotary
hammer does not damage the application tools.
Hold the retaining ring(22) of the keyless quick-change
chuck firmly in place. Open the tool holder by turning the
front sleeve(21) until the tool can be inserted. Hold the
retaining ring(22) in place and firmly tighten the front
sleeve(21) by turning it in the direction of the arrow until
you hear it click into place.
Check that it is seated securely by pulling on the tool.
Note: If the tool holder was unscrewed all the way, a scrap-
ing sound may be heard while retightening the tool holder
and it may not fully tighten.
In this case, turn the front sleeve(21) in the opposite direc-
tion to the arrow by one full turn. This will allow the tool
holder to be fully tightened.
Turn the combi switch(7) to the "drilling" position.
Removing the application tool (seefigureG)
Hold the retaining ring(22) of the keyless quick-change
chuck firmly in place. Open the tool holder by turning the
front sleeve(21) in the direction of the arrow until the
tool can be removed.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
Use a dust extraction system that is suitable for the ma-
terial wherever possible.
Provide good ventilation at the workplace.
It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Bosch Power Tools 1 609 92A 7SJ | (23.06.2022)
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GBH 18V-34 CF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GBH 18V-34 CF in de taal/talen: Alle talen als bijlage per email.

De handleiding is 7.25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info