1151
21
Verklein
Vergroot
Pagina terug
1/135
Pagina verder
English - 6
21 • F016 L70 362 • TMS • 24.01.06
Always use a Bosch low-kickback chain.
Apply the metal gripping teeth 11 for leverage.
Ensure correct chain tension.
General Behavior
Always hold the chain saw firmly with both
hands. Front grip with the left hand and rear grip with
the right hand. Fully grip both handles at all times
during operation. Never operate chain saw using
only one hand. Ensure power cord is located to the
rear, away from the chain and wood and so pos-
tioned that it will not be caught on branches or the
like during cutting.
Use the chain saw only with secure footing. Hold
the chain saw at the right-hand side of your body.
The chain must be running at full speed before it
makes contact with the wood. Use the metal grip-
ping teeth 11 to secure the saw onto the wood be-
fore starting to cut. Use the gripping teeth as a lev-
erage point “X” while cutting.
Reset the gripping teeth at a lower point when saw-
ing thicker logs by pulling the chain saw slightly
backwards until the gripping teeth release, and repo-
sition at lower level to continue sawing. Do not re-
move the saw completely from the wood.
Do not force the chain while cutting, let the chain do
the work, using the gripping teeth 11 to apply mini-
mal leverage pressure.
Do not operate the chain saw with arms fully ex-
tended or attempt to saw areas which are difficult to
reach, or on a ladder. Never use the chain saw
above shoulder height.
Sawing is optimized when the chain speed remains
steady during cutting.
Beware when reaching the end of the cut. The
weight of the saw may change unexpectedly as it
cuts free from the wood. Accidents can occur to the
legs and feet.
Always remove the saw from a wood cut while the
saw is running.
Cutting Logs
Observe the following safety instructions:
Support logs so that the face sides at the cut
do not close in against each other, which would re-
sult in the chain being jammed or pinched.
Position and set short logs safely prior to sawing.
Saw only wood or wooden objects. When sawing, al-
ways take care to avoid hitting stones, nails, etc., as
these could be thrown up or cause damage to the
chain or serious injury to the operator or bystanders.
Keep a running saw clear of wire fencing or the
ground.
Use of the saw to thin out branches or bushes is not
approved.
Length cuts must be carried out with care, as lever-
age with the gripping teeth 11 is not possible. Saw at
a flat angle to avoid kickback.
When working on a slope, operate above or to the
side of the trunk or laying tree.
Be careful not to trip over tree stumps, branches,
roots, etc.
Cutting Wood under Tension
There is a high risk of accidents when sawing wood,
branch or trees under tension. Be extremely careful.
Leave saw jobs like these to professionals.
When sawing logs supported on both ends, start the
cut from above (Y) about 1/3 of the diameter into the
log and then finish the cut (Z) from below, in order to
avoid splitting of the log or jamming of the saw.
Avoid contact of the chain saw with the ground.
When sawing logs supported on only one end, start
the cut from below (Y) about 1/3 of the diameter into
the log and finish the cut from above (Z), in order to
avoid log splitting or jamming of the chain saw.
Felling Trees
Always wear hard hat to protect head
against falling branches.
The chain saw can only be used to fell trees
smaller in diameter than the length of the chain
bar.
Secure work area. Ensure no persons or ani-
mals are in the vicinity of the falling tree.
Never attempt to free a jammed saw with the mo-
tor running. Use wooden wedges to free chain
and chain bar.
When cutting and felling operations are being per-
formed by two or more persons, at the same time,
the felling operations should be separated from the
cutting operation by a distance of at least twice the
height of the tree being felled. Trees should not be
felled in a manner that would endanger any person,
strike any utility line or cause any property damage.
If the tree does make contact with any utility line, the
company should be notified immediately.
The chain saw operator should keep on the uphill
side of the terrain as the tree is likely to roll or slide
downhill after it is felled.
An escape path should be planned and cleared
as necessary before cuts are started. The escape
path should extend back and diagonally to the rear
of the expected line of fall.
Before felling is started, consider the natural lean
of the tree, the location of larger branches and the
wind direction to judge which way the tree will fall.
Remove dirt, stones, loose bark, nails staples, and
wire from the tree.
Notching Undercut: Make the notch (X W) 1/
3 the diameter of the tree, perpendicular to the direc-
tion of falls as Make the lower horizontal notching cut
first. This will help to avoid pinching either the saw
chain or the guide bar when the second notch is be-
ing made.
D
E
F
G
E H
H
I
F016 L70 362 - GB Seite 6 Mittwoch, 25. Januar 2006 8:47 08
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch AKE 35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch AKE 35 in de taal/talen: Nederlands als bijlage per email.

De handleiding is 3,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Bosch AKE 35

Bosch AKE 35 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 139 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info