380711
43
Verklein
Vergroot
Pagina terug
1/66
Pagina verder
ENGLISH
ENGLISH
ENGLISH
43
Chopping with the Metal Blade
WARNING:
The metal blade (15) is very sharp! Danger of injury!
1. The safety cover (7) must be mounted on the drive shaft for
the mixing drive (6).
2. Mount the processor bowl as described.
3. Place the metal blade (15) directly over the locating pin.
Press the blade down as far as it will go (Illustration 6).
4. Cut the food up into smaller pieces beforehand. Now fi ll in
your ingredients. Please note the markings on the processor
bowl and do not fi ll it above them.
5. Place the lid in position on the processor bowl. Turn it to the
right until it is heard to lock in place.
6. Close the fi ller shaft (13) with the stopper (17).
7. Switch on the appliance and set a speed between 1 and 4
with switch (1). You will achieve better results if you use the
pulse mode.
8. After chopping, turn the switch (1) back to „0“ and pull out
the plug.
9. Turn the lid to the left and remove it from the processor
bowl.
10. Pull the blade off the locating pin.
11. Release and remove the grater bowl and the locating pin.
The contents can now be taken out of the bowl.
12. Clean the used parts as described in „Cleaning“.
Cutting and grating
1. The safety cover (7) must be mounted on the drive shaft for
the mixing drive (6).
2. Mount the processor bowl as described.
3. Place the locating pin over the drive shaft (9).
4. Push to the desired tool (11/12) into the tool holder (14)
(Illustration 8). Attach the tool holder to the locating pin
(Illustration 9).
WARNING:
The grater and rasp surfaces as well as the edges of the
inserts are very sharp! Danger of injury! Handle these
attachments with caution!
5. Place the lid in position on the processor bowl. Turn it to the
right until it is heard to lock in place (Illustration 10).
6. Insert the plug into a 230 V / 50 Hz socket installed accor-
ding to existing regulations and with earthing protection.
7. Switch the device on (Level 1 or 2 etc.) or use pulse operati-
on (PULSE) (See table).
8. Cut the food up into smaller pieces beforehand. Now fi ll the
ller shaft (13) with your ingredients. Use the fi ller (17) to
press the food into the fi lling slot. Exert a suffi cient degree
of pressure on the fi ller. The appliance must be switched on
only with the fi ller (17) mounted into place. Please note the
maximum fi lling level on the processor bowl.
9. After cutting/grating, turn the switch (1) back to „0“ and pull
out the plug.
10. Turn the lid to the left and remove it from the processor
bowl.
11. Please take off the tool holder from the locating pin.
12. Remove the locating pin from the drive shaft.
13. The processor bowl can now be removed. The contents can
now be taken out of the bowl .
14. Clean the used parts as described in „Cleaning“.
Always choose a utensil and a speed according to the following
table:
Product/Type of
Preparation
Max.
Quantity
Utensil Level
Max.
Operating
Time
Heavy dough (e.g. yeast
dough)
600 g Plastic blade
1 to 2,
P
2 min
Cake mixture 800 g Plastic blade
2 to 3,
P
2 min
Sponge mixture or wafer
mixture
800 g Plastic blade
2 to 3,
P
1 min
Cutting into small pieces,
e.g. fruit, vegetables,
herbs
500 g Metal blade
1 to 2,
P
1 min
Cutting cucumbers,
carrots
500 g Cutting utensil 1 to 2 1 min
Grating carrots, radish,
cheese
500 g Grater utensil 2 to 3 2 min
Grating potatoes, hard
cheese
500 g Grater utensil 1 to 2 2 min
Liquids, shakes up to 1,5 l Mixer vessel
3 to 4,
P
1 min
Whipped egg whites
min.
3 egg
whites
Plastic blade 3 or P 2 min
Cream min. 250 ml Plastic blade 2 to 4 2 min
Cleaning
Remove the plug from the socket before cleaning!
Clean the bowl and the mixing vessel carefully immediately
after each procedure. To do so, remove the bowl in order to
be able to clean off any residues on the drive shaft.
Never use sharp objects for cleaning!
Never use abrasive detergents!
Use a moist towel to clean the outside of the basis appli-
ance.
In the case of intensely colored foodstuffs (e.g. carrots), the
plastic parts can be stained: clean them with oil.
Any removable parts which have come into contact with
food (Tool and vessels) can be cleaned in soapy water.
ޥ NOTE:
The tools should be stored in the grater bowl in order to
prevent injuries. Place the metal blade on the guide pin fi rst of
all, followed by the plastic blade and then the tool holder.
05-KM 345 CB 43 14.11.2006, 9:28:01 Uhr
43

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bomann km 345 cb bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bomann km 345 cb in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Noors als bijlage per email.

De handleiding is 3,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info