426958
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
9
Using the template guide (fig. D)
The template guide can be used to make a cutout shape from
a template, for instance a letter.
Secure the template over the workpiece with double-
sided tape or ‘G’ clamps.
The router bit must extend below the flange of the
template guide, to cut the workpiece in the shape of the
template.
Using the distance piece (fig. E)
The distance piece can be used for trimming wooden or
laminate vertical projections.
Using the centring pin (fig. F)
The centring pin can be used to cut out circular patterns.
Drill a hole for the point of the centring pin in the centre
of the circle to be cut.
Place the router on the workpiece with the point of the
centring pin in the drilled hole.
Adjust the radius of the circle with the bars of the edge
guide.
The router can now be moved over the workpiece to cut
out the circle.
Using the copy follower (fig. G)
The copy follower helps to maintain an equal cutting distance
along the edge of irregularly shaped workpieces.
Place the router on the workpiece at the desired distance
from the edge to be copied.
Adjust the bars of the edge guide until the wheel is in
contact with the workpiece.
Switching on and off
Switching on
Keep the lock-off button (2) depressed and press the
on/off switch (1).
Release the lock-off button.
Switching off
Release the on/off switch.
Warning! Always operate the tool with both hands.
Routing
Fit the router bit and adjust to the required depth of cut as
described above.
Holding the tool firmly with both hands by the handles (3),
place the tool on the workpiece and switch on.
Allow the tool to build up speed before plunging down
into the workpiece. When the depth stop bar has been
contacted, operate the plunge lock lever (5).
Carry out the operation by applying a constant force both
downwards and in the direction of cut. Retain a firm grip
on the handles and be prepared for a possible reaction
force if the router bit suddenly stalls e.g. following
contact with a knot.
On completion of the operation, release the plunge lock
lever and control the upwards movement of the tool back
to its original position. When the tool has returned to its
original position, it can be switched off. Be aware that the
base is springloaded and that the tool will jump upwards
if not controlled.
Routing speed
The operating speed of the tool can be varied to affect the
level of finish. The correct speed selection will depend upon
the level of finish required, the type of material being
machined, the diameter and shape of the router bit.
Prepare the tool to make a practice cut on a piece of scrap
material. Make a preliminary adjustment of the speed
control selecting a high speed for small diameter router
bits and a low speed for large diameter router bits.
When the routing operation is completed, withdraw the
tool from the workpiece, switch off and the tool inspect
the level of finish. Adjust the speed control knob (4) and
repeat until an optimum level of finish is obtained.
Warning! Do not release the handles to adjust the speed
when the tool is locked down and operating in the workpiece.
Hints for optimum use
When working on outside edges, move the tool
counterclockwise (fig. N). When working on inside edges,
move the tool clockwise.
Use HSS router bits for softwood.
Use TCT router bits for hardwood.
You can use the tool without a guide (fig. O). This is
useful for signwriting and creative work. Only make
shallow cuts.
Refer to the table below for common types of router bits.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker xtw 1500 eka bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker xtw 1500 eka in de taal/talen: Engels als bijlage per email.

De handleiding is 1,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info