426958
8
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
8
Fitting the distance piece (fig. E)
Fit the distance piece (14) to the base of the router using
the screws provided.
Fitting the centring pin (fig. F)
Fit the edge guide to the router as shown in fig. B,
but upside down.
Fit the centring pin (15) to the workpiece side of the edge
guide with the screw (25) provided.
Fitting the copy follower (fig. G)
Fit the edge guide to the router as shown in fig. B.
Fit the ‘L’ bar (16) to the upper side of the edge guide
using the two screws and nuts provided.
Adjust the rotating attachment (26) on the ‘L’ bar with the
wing knob (27).
Fitting the additional edge guide (fig. H)
The additional guide (21) is designed to allow routing of a thin
piece of wood (e.g. the edge of a door).
Adjust the edge guide (12) as necessary.
Loosen the fixing screws (28).
Fit the edge guide (21) to the bars (19) protruding from the
router base.
Adjust the edge guide so the workpiece becomes clamped
between the two edge guide.
Tighten the fixing screws (28).
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
cutting it.
Adjusting the depth of cut (fig. I, J & K)
The depth of cut is the distance X between the depth stop bar
(9) and the depth stop (29). The depth of cut can be set in two
different ways as described below.
Adjusting the depth of cut using the scale (fig. J)
Fit the router bit as described above.
Loosen the locking screw (30).
Pull the plunge lock lever (5) up.
Plunge the router down until the router bit touches the
workpiece.
Push the plunge lock lever (5) down.
Move the depth stop bar (9) down against the depth stop
using the depth stop adjuster (31). Reset the scale by
aligning the zero marking (32) with the arrow (33).
Move the depth stop bar (9) to the calculated position
using the depth stop adjuster (31). One quarter turn
corresponds to approx. 6.25 mm.
Tighten the locking screw (30).
Fine adjust using the adjusting knob (34). One full turn
corresponds to approx. 1 mm.
Pull the plunge lock lever (5) up and return the router to its
original position.
After switching the router on, plunge it down and make
the desired cut.
Adjusting the depth of cut using a piece of wood (fig. K)
Fit the router bit and plunge the router down as described
above.
Loosen the locking screw (30).
Move the depth stop bar (9) up using the depth stop
adjuster (31).
Place a piece of wood with a thickness equal to the
desired depth of cut between the depth stop (29) and the
depth stop bar (9).
Move the depth stop bar (9) down against the wood using
the depth stop adjuster (31).
Tighten the locking screw (30).
Fine adjust using the adjusting knob (34).
Remove the piece of wood.
Pull the plunge lock lever (5) up and return the router to its
original position.
After switching the router on, plunge it down and make
the desired cut.
Adjusting the revolver depth stop (fig. L)
After turning the revolver depth stop to the desired setting,
you can fine-adjust the depth stop to be used. If you want to
make several cuts with a different depth of cut, adjust each of
the depth stops.
Turn the depth stop screw (35) up or down as required
using a screwdriver.
Setting the speed
Set the speed control knob (4) to the required speed.
Use a high speed for small diameter router bits. Use a low
speed for large diameter router bits.
Using a batten as a guide (fig. M)
When it is not possible to use the edge guide, for example
when routing grooves in the back panel of a bookcase to
support shelves, proceed as follows:
Select a piece of wood with a straight edge to use as a
batten.
Place the batten onto the workpiece.
Move the batten until it is in the correct position to guide
the tool.
Securely clamp the batten to the workpiece.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker xtw 1500 eka bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker xtw 1500 eka in de taal/talen: Engels als bijlage per email.

De handleiding is 1,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info