585428
10
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
10
ENGLISH
(Original instructions)
11
ENGLISH
(Original instructions)
u Release the head-release button clockwise.
Note: The head will only rotate in one direction.
Edging
When being used as an Edger, stones, pieces of metal and
other objects can be thrown out at high speed by the line. The
trimmer and guard are designed to reduce the danger. How-
ever, MAKE SURE that other persons and pets are at least
100 feet (30m) away. Optimum cutting results are achieved on
edges deeper than 2 inches (50 mm).
u Do not use this trimmer to create trenches.
u Using the edging wheel (7), guide the trimmer as shown in
gure K.
u Position the edging wheel on the edge of the sidewalk or
abrasive surface so the cutting line is over the grass or dirt
area to be edged.
u To make a closer cut, slightly tilt the trimmer.
Replacement accessories
Before you begin trimming, only use the appropriate type of
cutting line. Use BLACK+DECKER replacement spool Model
No. AF-100, and replacement cap RC-100. Reload nylon line
(either bulk or prewound replacement spool) as shown in this
manual.
u USE ONLY .065 inch (1.65 mm) DIAMETER ROUND
NYLON MONOFILAMENT LINE. Do not use serrated or
heavier gauge line, as they will overload the motor and
cause overheating, and will not feed properly. This line is
available at your local dealer or authorized service center.
uOther replacement parts (guards, spool caps, etc.) are
available through BLACK+DECKER service centers.
Warning! The use of any accessory not recommended by
BLACK+DECKER for use with this trimmer could be hazard-
ous.
Hints for optimum use
Replacing the spool
uRemove battery from trimmer.
u Depress the tabs (15) and remove the spool cap (9) from
the spool housing (16) in the trimmer head (g. M).
u For best results, replace spool with BLACK+DECKER
model # AF-100.
u Grasp empty spool with one hand and spool housing with
other hand and pull spool out.
uIf lever (17) in base of housing becomes dislodged,
replace in the position as shown in (g. N) before inserting
new spool into housing.
u Remove any dirt and grass from the spool and housing.
u Unfasten the end of the cutting line and guide the line into
the eyelet (19) (g. O).
uTake the new spool and push it onto the boss (18) (g. N)
in the housing. Rotate the spool slightly until it is seated.
The line should protrude approximately 5-3/8 inches
(136mm) from the housing.
u Align the tabs on the spool cap with the slots (20) in the
housing (g. O).
uPush the cap onto the housing until it snaps securely into
place.
CAUTION: To avoid trimmer damage, if the cutting line
protrudes beyond the trimming blade, cut it off so that it just
reaches the blade.
Rewinding spool from bulk line (use only .065 in.
ROUND diameter line)
Bulk line is also available for purchase from your local retailer.
To install bulk line, follow the steps below:
uRemove battery from trimmer.
uRemove the empty spool from the trimmer as described in
“Replacing the spool”.
uRemove any remaining cutting line from the spool.
u Make a fold at the end of the cutting line at about 3/4 inch
(19mm) (21). Feed the cutting line into one of the line
anchoring slots (22) as shown in (g. P).
uInsert the 3/4 inch (19mm) end of the bulk line into the
hole (23) in the spool adjacent to the slot as shown in
(g. Q). Make sure the line is pulled tight against the spool
as shown in (g. Q).
u Wind the cutting line onto the spool in the direction of the
arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross (g. R).
uWhen the wound cutting line reaches the recesses (24),
cut the line. (g. Q).
uFit the spool onto the trimmer as described in “Replac
ing the spool”.
NOTE: Hand wound spools from bulk line are likely to become
tangled more frequently than BLACK+DECKER factory
wound spools. For best results, factory wound spools are
recommended.
Handwound replacement spools:
#A6170 (25cm) #A6171 (40cm).
Troubleshooting
If your tool seems not to operate properly, follow the instruc-
tions below. If this does not solve the problem, please contact
your local BLACK+DECKER repair agent.
Warning! Before proceeding, remove the battery from the
tool.
Appliance runs slowly
u Check that the spool housing can rotate freely. Carefully
clean it if necessary.
u Check that the cutting line does not protrude more than
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
uKeep the tabs depressed and remove the spool cover
from the housing.
uPull the cutting line until it protrudes 11 cm from the hous-
ing. If insufcient cutting line is left on the spool, install a
new spool of cutting line as instructed above.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Black-Decker-STC1840

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker STC1840 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker STC1840 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 8,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info