585428
9
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
8
ENGLISH
(Original instructions)
9
ENGLISH
(Original instructions)
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the position of the auxiliary handle (g.
G)
The auxiliary handle (3) can be adjusted to provide optimum
balance and comfort.
u Loosen the knob (12) on the bolt (11) by truning it counter-
clockwise.
u Gently slide the second handle up and down the tube (10)
to the desired hight for comfort.
u Tighten the knob (12) onto the bolt by turning it clockwise.
Adjusting the height of the tool (g. H)
This tool has a telescopic mechanism, allowing you to set it to
a comfortable height.
To adjust the height setting, proceed as follows:
u Release the hight adjust locking clamp (5).
u Gently pull the tube (10) up or down to the desired height.
u Close the hight adjust locking clamp (5).
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
Warning! Before assembly, remove the battery from the tool.
u Remove the tape holding the cutting line to the spool
housing (9).
Fitting and removing the battery (g. $)
u To t the battery (2), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
u To remove the battery, push the release button ($) while at
the same time pulling the battery out of the receptacle.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (g. C)
The battery needs to be charged before rst use and whenev-
er it fails to produce sufcient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u To charge the battery (2), insert it into the charger. The
battery will only t into the charger in one way. Do not
force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
The charging indicator will ash green continuously (slowly).
The charge is complete when the charging indicator lights
green continuously. The charger and the battery can be left
connected indenitely with the LED illuminated. The LED will
change to ashing green (charging) state as the charger oc-
casionally tops up the battery charge. The charging indicator
will be lit as long as the battery is connected to the plugged-in
charger.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator will ash red at a fast rate. Proceed as follows:
u Re-insert the battery (2).
u If the charging indicators continues ashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
ash at each speed and repeat.
Switching on and off
u To switch the trimmer on, pull the lock off button (13)
(shown in inset, gure I) back toward the battery (2) and
then squeeze the trigger switch (1).
u To switch the trimmer off, release the trigger switch.
Operating the trimmer
u With the unit on, angle unit and slowly swing the trimmer
side to side as shown in gure I.
u Maintain a cutting angle of 5° to 10° as shown in gure I1.
Do not exceed 10° (g I2). Cut with the tip of the line. To
keep distance from hard surfaces use edge guide (7).
u Maintain a minimum distance of 24 inches (609.6 mm)
between the guard and your feet as shown in (g. I1). To
acheive this distance adjust the overall height of the trim-
mer as shown in (g. H).
Converting to edging mode (g. J & K)
The wheeled edge guide should only be used when in the
edging mode. The trimmer can be used in trimming mode or
edging mode to trim overhanging grass along lawn edges and
ower beds. For edging, the trimmer head should be in the
position shown in (g. K). If it is not:
u Remove the battery from the trimmer.
u Press and hold the head-release button (14) as shown in
(g. J).
u While holding the auxillary handle (3), rotate the head (6)
counterclockwise.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Black-Decker-STC1840

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker STC1840 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker STC1840 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 8,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info