527583
11
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
7
ENGLISH
B2
Do not cut wet grass, best results are
achieved when the grass is dry.
B3
Cut at an angle and with the tip of the nylon
line. Your trimmer is balanced to operate at
this angle.
B4
Swing your trimmer gently from side to side.
B5
Do not overload your trimmer. It operates
best at high speeds.
B6
On long grass, start at the top.
B7
Take small cuts.
B8
If your trimmer features a cord restraint,
loop a length of cord through the restraint to
prevent the plug and socket coming apart
accidentally if the cord is pulled.
How to fit a new spool of cutting line
(Fig. F & G)
Disconnect your trimmer from the
power supply.
F
Remove the spool cover by pushing the
two spool cover tabs (12) inwards and
upwards (Fig. F), then pull off (it is not
necessary to push both tabs in at the
same time). The empty spool can now
be withdrawn from the drive shaft.
Remove any dirt or grass that may have
collected inside the spool housing and
cover.
Unwind approximately 9cm (3.5") of
cutting line (5) from the new spool (15)
and temporarily park the cutting line end
in one of the ‘L’ shaped slots to prevent
the line unravelling.
G
Feed the cutting line through the eyelet
(14) and then push the spool onto the
centre drive shaft while pulling the free
end of the line to release it from the ‘L
shaped slot. To fully seat the spool,
rotate as necessary, taking care not to
trap the cutting line underneath the spool
and making sure that there is a minimum
of 9cm (3.5") protruding from the
spool housing.
Replace the spool cover by aligning
both tabs on it (12) with the slots in the
spool housing and pushing them into
place. Make sure that both tabs are
securely located.
How to wind new line onto an empty
spool (Fig. H & J)
H
A maximum of 10 metres of new cutting
line can be wound onto the empty spool.
The spool has an ‘Indicator’ to help you
avoid winding an excessive quantity of
cutting line on the spool, as too much will
prevent the automatic feed system from
functioning.
Remove any remnant of old cutting line
from the spool (15).
J1
Push the end of the new cutting line into
one of the two retaining holes (17) provided
in the spool (15) and insert 20mm.
Bend the cutting line over, pulling it
through the adjacent ‘L’ shaped slot.
The cutting line should now be firmly
anchored to the spool and you may
proceed to wind it on in the direction of
the arrow (16).
J2
Take time to wind the cutting line on
neatly, in layers. Do not criss cross.
When you have wound on sufficient
cutting line, temporarily park it in one of
the ‘L’ shaped slots to prevent the spool
unravelling, ensuring you leave a
minimum of 9cm (3.5") protruding.
Fit the spool and spool cover (8) to the
spool housing as described for fitting a
new spool.
Replacement line
A new spool containing 10 metres of nylon line may
be purchased from your Black & Decker agent.
Alternatively, replacement packs containing 25 to
50 metres of line are available.
For maximum reliability never put on a heavier or
lighter line (eg. fishing line) which will prevent the
automatic feed from functioning, cause motor failure
or reduce cutting performance.
Care and maintenance
For the best performance, please keep the nylon
line, spool and air slots in your trimmer body
clean. Use a dry brush or cloth to remove grass,
sap or other dirt.
Plastic parts may be cleaned by using a mild
soap and a cloth dampened with hot water.
Do not use any other type of detergent, cleaner
GL340 UK p02-11 w/p 24/3/00, 2:17 pm7
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GL340 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GL340 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info