680440
30
Verklein
Vergroot
Pagina terug
1/144
Pagina verder
NOTE:
• Contrary to the illustrated section, use the appropriate
connectors (e.g. for timber gates use woodscrews), as
well as the proper hole depths for other gate types.
• Contrary to the illustrated section, the required core hole
diameter may vary depending on material thickness or
strength. The required diameter may be Ø 5.0–5.5 mm
for aluminium and Ø 5.7 5.8 mm for steel.
Fitting:
See Figures4–4.3
The sliding gate operator must be released (see Figure3.2).
When fitting the toothed tracks, make sure that the
transitions between the individual toothed tracks are
properly aligned to ensure smooth gate movement.
After fitting, the toothed tracks and the toothed wheel of
the operator must be aligned to each other. Both the
toothed tracks and the operator housing can be adjusted
to do this.
Incorrectly fitted or poorly aligned toothed tracks may
lead to unintentional reversing. It is essential that the
specified dimensions are adhered to!
Seal the housing to protect it from humidity and vermin
(see Figure 4.4).
3.4 Sliding gate operator electrical connection
See Figure4.5
DANGER
Mains voltage
Contact with the mains voltage presents the danger of a
deadly electric shock.
For that reason, observe the following warnings under all
circumstances:
Electrical connections may only be made by a qualified
electrician.
The on-site electrical installation must conform to the
applicable protective regulations (230 / 240VAC,
50 / 60Hz)!
The mains plug must be disconnected before any work
is performed on the operator.
Connect the mains voltage directly at the transformer
plug terminal using theNYY underground cable.
3.5 Fitting the circuit board bracket
See Figure4.6
1. Fasten the circuit board bracket using the two screws
loosened earlier,
D
, as well as two additional screws
from the scope of delivery.
2. Replace the connecting terminals.
3.6 Fitting the magnet holder
See Figure4.7
1. Push the gate by hand into the CLOSE end-of-travel
position.
2. Fully preassemble the magnet slide in the centre position.
3. Fit the toothed track clip so that the magnet is offset by
approx. 20mm from the reed contact in the circuit board
bracket.
3.7 Locking the operators
See Figure5
The operator is engaged once locked.
Turn the mechanism back to the lock position while
slightly raising the motor.
3.8 Connecting additional
components / accessories
See the control print overview in Figure6
WARNING
Danger of injury due to unwanted
gate travel
Incorrectly attached control devices
(e.g.buttons) may trigger unwanted gate
travel. Persons or objects may be
trapped as a result.
Install control devices at a height of
at least 1.5m (out of the reach of
children).
Fit permanently installed control
devices (such as buttons, etc.)
within sight of the gate, but away
from moving parts.
Persons or objects may be trapped if the
installed safety equipment fails.
In accordance with BGR232, install
at least one clearly visible and easily
accessible emergency command
unit (emergency OFF) near the gate
so the gate can be brought to a
standstill in the case of danger
(seesection3.8.3)
ATTENTION
Damage to the electronics caused by external voltage
External voltage on the connecting terminals of the control
will destroy the electronics.
Do not apply any mains voltage (230 / 240VAC) to the
connecting terminals of the control.
The total consumed current may be max.500mA when
connecting accessories at the following terminals:
• 24V= • SE3 / LS
• Ext.radio • SE1 / SE2
3.8.1 Connecting an external radio receiver
See Figure6.1
Connect the wires of the external radio receiver as
follows:
GN to terminal20 (0V)
WH to terminal 21 (channel 1 signal)
BN to terminal5 (+24V)
YE to terminal23 (channel2 signal for partial
opening). Only with a 2-channel receiver.
NOTE:
The aerial wire of external radio receivers should not come
into contact with metal objects (nails, bracing, etc.). The best
orientation to achieve an optimum range must be established
by trial and error.
30
C300 - C800 / Rev. 1.1 RE / 07.2014
ENGLISH
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Berner C500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Berner C500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 12,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info