577174
18
Verklein
Vergroot
Pagina terug
1/97
Pagina verder
09/ 2013
BENNING CM 1-1/ 1-2
12
20 kΩ 10 ± (0.7 % of the measured value + 2 digits) 1.3 V
200 kΩ 100 ± (0.7 % of the measured value + 2 digits) 1.3 V
2 M 1 kΩ ± (1.0 % of the measured value + 2 digits) 1.3 V
20 M 10 kΩ ± (1.9 % of the measured value + 5 digits) 1.3 V
The integrated buzzer sounds if the resistance R is lower than 20 Ω.
The change-over point of the range selection might be already at a value of
1400!
8. Measuring with the BENNING CM 1‑1/ 1‑2
8.1 Preparing the measurement
Operate and store the BENNING CM 1-1/ 1-2 at the specied storage and op-
erating temperatures only! Do not permanently expose the device to sunlight.
- Check stated nominal voltage and nominal current on the safety measuring
leads. Nominal voltage and current of the enclosed safety measuring leads
comply with the respective values of the BENNING CM 1-1/ 1-2.
- Check insulation of the safety measuring leads. If the insulation is damaged,
the safety measuring leads must be replaced immediately.
- Check the safety measuring leads for continuity. If the conductor in the
safety measuring lead is interrupted, replace the safety measuring leads
immediately.
- Before selecting another function by means of the sliding switch
7
, discon-
nect the safety measuring leads from the measuring point.
- Strong sources of interference in the vicinity of the BENNING CM 1-1/ 1-2
might involve unstable readings and measuring errors.
8.2 Voltage measurement ( BENNING CM 1-2)
Do not exceed the maximum permitted voltage with respect to
earth potential! Electrical danger!
The highest voltage which may be applied to the
- COM jack
9
- jack for V and Ω
8
of the BENNING CM 1-2 against ground is 600 V.
- Select the desired function (V AC/ DC) by means of the sliding switch
7
of
the BENNING CM 1-2. Select the desired function AC or DC by means of
the shift key (V~/ V ).
- Connect the black safety measuring lead to the COM jack
9
of the
BENNING CM 1-2.
- Connect the red safety measuring lead to the jack for V and Ω
8
of the
BENNING CM 1-2.
-
Bring the safety measuring leads into contact with the measuring points and
read the measured value on the digital display
1
of the BENNING CM 1-2.
See gure 2: DC voltage measurement
See gure 3: AC voltage measurement
8.3 AC current measurement
8.3.1 Preparin g the measurement
Operate and store the BENNING CM 1-1/ 1-2 at the specied storage and oper-
ating temperatures only. Do not expose the device to permanent sunlight.
- Strong sources of interference in the vicinity of the BENNING CM 1-1/ 1-2
might involve unstable readings and measuring errors.
Do not apply any voltag to the output contacts of the
BENNING CM 1‑1/ 1‑2! Any possibly connected safety measur
ing leads have to be removed.
8.3.2 AC current measurement
-
Use the sliding switch
7
to select the desired range on the BENNING CM 1-1
or
the desired function (A AC) on the BENNING CM 1-2.
- Operate the opening lever
J
and clamp the single-wire live conductor cen-
trally by means of the clamp of the BENNING CM 1-1/ 1-2.
- Read the value indicated on the digital display
1
.
See gure 4: AC current measurement
8.4 Resistance measurement and acoustic continuity test
( BENNING CM 1-2)
- Select the desired function (  ) by means of the sliding switch
7
of the
BENNING CM 1-2.
- Connect the black safety measuring lead to the COM jack
9
of the
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Benning CM1.1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Benning CM1.1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Turks, Zweeds als bijlage per email.

De handleiding is 4,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info