Handleiding Behringer Xenyx X2442USB (pagina 13 van 19) (Engels)

660523

Verklein

Vergroot

Pagina terug

1/19

Pagina verder

13 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual

FBQ FEEDBACK DETECTION

The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the

frequency band faders to indicate the critical frequencies. On a per-need basis,

lower the frequency range in question somewhat in order to avoid feedback.

Thegraphic stereo equalizer has to be turned on in order to use this function.

◊ Logically, at least one (ideally several) microphone channels have to be

open for feedback to occur at all!

Feedback is particularly common when stage monitors (“wedges”) are

concerned, because monitors project sound in the direction of microphones.

Therefore, you can also use the FBQ Feedback Detection for monitors by placing

the equalizer in the monitor bus (see MAIN MIX/MONITOR).

4. Digital Eects Processor

24-BIT MULTI-EFFECTS PROCESSOR

Here you can nd a list of all presets stored in the multi-eects processor.

Thisbuilt-in eects module produces high-grade standard eects such as reverb,

chorus, anger, delay and various combination eects. Use the Aux Send FX on

the channels and the Aux Send FX master control to determine the input signal of

the eects processor.

X1832USB

Fig. 4.1: Digital eects module

The built-in stereo eects processor has the advantage that it does not need to

be wired up. This excludes the danger of humming or level mismatch right from

the start and thus considerably facilitates use.

These eect presets are classical “mixing eects”. If you move the STEREO AUX

RETURN FX control, you mix the channel signal (dry) and the eect signal. Youcan

control the balance between the two signals with the channel fader and the

STEREO AUX RETURN FX control.

FX OUT

Mixing consoles X2222USB and X2442USB have a separate output for the eects

device, which is unbalanced and stereo (tip = left signal; ring = right signal;

sleeve = ground/shielding). Thus, you can record, for example, a vocal track

enhanced with reverb in parallel to a “dry” vocal track; when doing the mix-down

later on, you can freely determine the amount of reverb added.

◊ The X2442USB has the effect output on the rear, X2222USB has it

located next to the aux sends on the front panel.

FX FOOTSW.

Connect a standard foot switch to the foot switch jack and use this to switch

the eects processor on and o. A light at the bottom of the display indicates

wheater the eects processor has been muted by the foot switch.

◊ In Chapter 6.2 you will find an illustration showing how to connect your

foot switch correctly.

LEVEL

The LED level meter on the eects module should display a suciently high

level. Take care to ensure that the clip LED only lights up at peak levels. If it is

lit constantly, you are overloading the eects processor and this could cause

unpleasant distortion.

PROGRAM

You can select the eect preset by turning the PROGRAM control. The display

ashes with the number of the current preset. To recall the selected preset,

presson the button; the ashing stops. You can also recall the selected preset

with the foot switch.

5. Rear Panel Connectors

5.1 Main mix outputs, insert points and control

room outputs

X2442USB

Fig. 5.1: Main Mix outputs, main mix insert points and control room outputs

MAIN OUTPUTS

The MAIN outputs carry the MAIN MIX signal and are on balanced XLR jacks with

a nominal level of +4 dBu. In parallel with this, ¼" phone jacks carry the main

mix signal in a balanced format (X1622USB: here, the phone jack outputs are

unbalanced and located on the front panel).

CONTROL ROOM OUTPUTS (CTRL OUT)

The control room output is normally connected to the monitoring system in the

control room and carries the stereo mix or, when selected, the solo signals.

MAIN INS(ERTS) (X2442USB only)

These are the insert points for the main mix. In the signal path, they are

post-main mix amp, but pre-main fader(s). Use them to insert, for example,

adynamics processor or graphic equalizer. Please also note the information on

insert points in chapter 5.3.

5.2 Subgroup outputs

Fig. 5.2: Subgroup outputs

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Behringer Xenyx X2442USB Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Behringer Xenyx X2442USB

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info